1.
Run the IP Camera Tool, and assign an IP address for your
camera.
If you need to access your IP camera outside of your LAN, you
need to configure some settings on your router. Please follow the
corresponding steps:
2.
Enable UPnP and DDNS in the camera’s settings page. We
recommend you to use the Foscam DDNS by factory default, but
if you want to use the third party DDNS, please check the user
manual for further instructions.
4.
Now you can access your IP camera by https://domain name:
HTTPS port via the Internet.
Foscam Digital Technologies LLC
www.foscam.us
WPS (Wi-Fi Protected Set-up)
We recommend that you use WPS function to setup wireless
connection.
If your wireless router doesn't support WPS function,please
setup by the following steps.
OUT
IN
ANT
SD
DC 5V
WPS Button
1.
Press and hold the WPS button for two seconds.
Input the port and IP address
of your camera and click Save.
2.
Press the WPS button on your wireless router within 60 seconds.
The WPS button is usually on the front or back of your router. If you
are not sure about the WPS function of your router, please refer to
your router’s User Manual.
3.
The camera will automatically create a secure wireless connection
to your router in about 60 seconds. If you have connected the
network cable, please disconnect it.
:
Please set the security mode of your router to WPA-PSK/WPA2-PSK,
or the WPS settings may be failed.
Note:
1.
Choose “
Settings
” on the top of the camera page, then go to the
“
Network - Wireless Settings
” section on the left side of the screen,
then click
Scan
.
2.
Click the SSID (name of your router) in the list, and the
corresponding SSID and encryption will be filled into the relevant
fields automatically on the right side of the page. All you need to
do is input the password for your wireless network.
3.
Click the
Save
button and disconnect the network cable. Don’t
power off the camera until it is able to show up in the IP Camera
Tool. If the camera does not show up, try unplugging the power
cord from the camera and plugging it back in. It should connect to
the wireless network automatically.
3.
Configure port (HTTPS port) forwarding on your router. For
these steps, we will be using the TP-LINK brand wireless router as
an example. First, we need go to the “
Forwarding – Virtual
Servers
” panel for setup. For other brands, you can check the user
guide or user manual of the router, or consult the manufacturer.
Click Add New.
While we hope your experience with the IPCAM network camera
is enjoyable and easy to use, you may experience some issues or
have questions that this User’s Guide has not answered.
Please contact support via e-mail at
You
can also reach technical support at
1-800-930-0949
by following
the automated instructions.
Click through different pages to see
other wireless networks if there are
more than 10.
Select
Yes
and click
Save
.
Click
Enable DDNS
and click
Save
.
The content in the Manufacture’s
DDNS column is the domain name of
your camera.
1. Click the SSID (name) of your router,
and the corresponding information will
be filled in the fields.
2. Input the password of
your router.
Here you have finished the Port
Forwarding setup.
4
Wireless Connection
5
Remote Access
7
Technical Support
6
Access the IP Camera by
Smart Phone
If you want to access your camera on smart phone, please search
and install
Foscam Viewer
on APP Store or Google Play for iOS
or Android devices.
For details, please refer to the Android or iOS User Manual in the
CD.
You can see the port of your camera here.
If you want to set Remote Access for several cameras on the same
network, you will need to change the HTTPS port for each camera.
Notes:
If you forget your username or password, you can press and
hold the reset button on the bottom of the camera using a pin for
5 seconds. This resets the camera to factory defaults.
If you want to access your camera over wireless or the Internet,
please continue with the setup by following the Wireless and
Remote Access steps below.
Right click your camera and
click Network Configuration.
FI9831W
IP Address
: Set this in the same
subnet as your computer , or keep
it as default.
Subnet Mask
: Keep it as default.
Gateway
and
DNS Server
: Set it to
the IP address of your router.
Input the Username and
password, click
OK
.
FI9821W
FI9821W