5.
After
logging in, you will see live video on the interface.
4
Wireless Connection
2.
Click the SSID (name of your router) in the list, and the
corresponding SSID and encryption will be filled into the
relevant fields automatically on the right side of the page. All
you need to do is input the password for your wireless
network.
1.
Choose “Settings” on the top of the camera page, then go to
the “Network - Wireless Settings” section on the left side of the
screen, then click
Scan
.
3.
Click the
Save
button and disconnect the network cable.
Don’t power off the camera until it is able to show up in the
IP Camera Tool. If the camera does not show up, try
unplugging the power cord from the camera and plugging it
back in. It should connect to the wireless network
automatically.
5
Remote Access
Input the username and
password, click
OK
.
IP Address: Set this in the same
subnet as your computer , or keep
it as default.
Subnet Mask: Keep it as default.
Gateway and DNS Server: Set it to
the IP address of your router.
Right click your camera and
click Network Configuration.
2.
Enable UPnP and DDNS in the camera’s settings page. We
recommend you to use the Foscam DDNS by factory default,
but if you want to use the third party DDNS, please check the
user manual for further instructions.
3.
Configure port (HTTPS port) forwarding on your router. For
these steps, we will be using the
TP-LINK brand wireless router as
an example. First, we need go to the “Forwarding – Virtual
Servers” panel for setup. For other brands, you can check the user
guide or user manual of the router, or consult the manufacturer.
Click
Enable DDNS
and click
Save
.
The content in the Manufacture’s
DDNS column is the domain name
of your camera.
You can see the port of your camera here.
If you want to set Remote Access for several cameras on the same
network, you will need to change the HTTPS port for each camera.
4.
Now you can access your IP camera by https://domain name:
HTTPS port via the Internet.
7
Technical Support
If you have problems with your Foscam IP Camera, please
contact the Foscam reseller you purchased from,or you can
e-mail the Foscam headquarter technical support team:
.
Your valuable comments and suggestions on improving
Foscam products are welcomed!
WPS (Wi-Fi Protected Set-up)
We recommend that you use WPS function to setup wireless
connection.
If your wireless router doesn't support WPS function,please
setup by the following steps.
OUT
IN
ANT
SD
DC 5V
WPS Button
1.
Press and hold the WPS button for two seconds.
Click Add New.
If you need to access your IP camera outside of your LAN, you
need to configure some settings on your router. Please follow
the corresponding steps:
1.
Run the IP Camera Tool, and assign an IP address for your
camera.
Input the port and IP address
of your camera and click Save.
443
443
6
Access the IP Camera
by Smart Phone
If you want to access your camera on smart phone, please
search and install
Foscam Viewer
on APP Store or Google
Play for iOS or Android devices.
For details, please refer to the iOS or Android User
Manual in the CD.
Click through different pages to see
other wireless networks if there are
more than 10.
1. Click the SSID (name) of your router,
and the corresponding information will
be filled in the fields.
2. Input the password of
your wireless network.
2.
Press the WPS button on your wireless router within 60 seconds.
The WPS button is usually on the front or back of your router. If you
are not sure about the WPS function of your router, please refer to
your router’s User Manual.
3.
The camera will automatically create a secure wireless
connection to your router in about 60 seconds. If you have
connected the network cable, please disconnect it.
Note:
Please set the security mode of your router to
WPA-PSK/WPA2-PSK, or the WPS settings may be failed.
Notes:
If you forget your username or password, you can press
and hold the reset button on the bottom of the camera
using a pin for 5 seconds. This resets the camera to factory
defaults.
If you want to access your camera over wireless or the
Internet, please continue with the setup by following the
Wireless and Remote Access steps below.
After logging in for the first time, it will go to "Setup
Wizard” automatically. Please set the basic parameters, such
as camera name, camera time, wireless settings and so on.
Select
Yes
and click
Save
.