Fortress Technologies FWAD08M18, Руководство пользователя

Страница: 10 / 40

REMOTE CONTROL OPERATION
3
5
2
1
4
9
8
10
11
1
TEMP DOWN Button
Press the button to increase the set (operating)
temperature of the unit. Each time the button is
pressed the temperature increases 1°C (Celsius scale).
O
Maximum setting is 30 C.
2
TEMP UP Button
Press the button to decrease the set (operating)
temperature of the unit. Each time the button is pressed
the temperature decreases 1°C (Celsius Scale).
O Minimum setting is 17 C.
Press this button to modify the air conditioner mode in a
sequence of following:
3
MODE Button
SWING Button
TIMER ON Button
8
9
TIMER OFF Button
10
CAUTIONS
9
6
7
ON/OFF Button
Press the "ON/OFF" button to turn the appliance ON/OFF.
FAN Button
Auto LOW MED HIGH
Press the " TIMER OFF" button to activate the auto off
time setting. Each press will increase the time setting in
30 minutes increments, up to 10 hours, then at 1 hour
increments up to 24 hours. To cancel the auto off time
setting, press the button until the time setting is 0.
11
MODE
FAN
TEMP
SLEEP
TURBO
LED
ON/OFF
SHORT
CUT
TIMER
ON
TIMER
OFF
4
SLEEP Button
Press the "SLEEP" button to activate/deactivate the
"SLEEP" feature. In the COOL mode, the cooling
temperature set point will increase 1°C per hour after the
"SLEEP" mode is activated. Two hours later, the set point
will not be changed and the fan speed will be kept on
LOW .
Note: When activating the SLEEP mode in AUTO mode,
the set temperature will not be changed over time.
6
7
SHORTCUT Button
Used to restore the current settings or resume previous
settings. On the first time connecting to the power, if push the
SHORTCUT button, the unit will operate on AUTO mode,
26°C, and fan speed is Auto.
Push this button when remote controller is on, the system
will automatically revert back to the previous settings including
operating mode, setting temperature, fan speed level and
sleep feature(if activated).
If pushing more than 2 seconds, the system will automatically
restore the current operation settings including operating
mode, setting temperature, fan speed level and sleep feature
(if activated ).
Press this button to activate the auto-on time setting.
Each press will increase the auto-timed setting in 30 minutes
increments. When the setting time displays 10, each press
will increase the auto-timed setting 60 minutes increments.
To cancel the auto-timed program, simply adjust the auto-on
time to 0.0.
12
LED Button
Disable/Active indoor screen Display.When pushing the
button, the indoor screen display is cleared, press it again
to light the display.
5
TURBO Button
Active/Disable Turbo function. Turbo function enables
the unit to reach the preset temperature at cooling or
heating operation in the shortest time(if the indoor unit
does not support this function, there is no corresponding
operation happened when pressing this button.)
12
NOTE
：
Heat mode is not supported by the cooling only appliance.
AUTO COOL DRY HEAT FAN
Used to select the fan speed in four steps:
Note:
You can not switch the fan speed in AUTO or DRY mode.
Used to stop or start vertical louver movement and set the
desired left/right air flow direction. The vertical louver changes
6 degree in angle for each press. And the temperature display
area of indoor unit displays for one second. If keep pushing
more than 2 seconds, the vertical louver swing feature is activated.
And the display area of indoor unit displays , flashes four
times, then the temperature setting reverts back.
If the vertical louver swing feature is stopped, it displays
and remains on for 3 seconds.
NOTE: For some units , the indoor units display when the
swing feature is activated, and display when the swing
feature is stopped.
Use the remote control within a distance of 5 meters from the air conditioner. A sound of beep will be generated by the
air conditioner when signals received.
Never immerse the remote control in water or other liquids. Do not put it under direct sunshine.
If the signal receiver on the air conditioner is exposed to direct sunshine, the air conditioner may be not function properly.
Remove the batteries in the remote control if it is not in use for prolonged period.
fortress