Place the mounting plate against the wall and
insert the toggle wings into the holes in the wall
to mount the plate.
NOTE:
Before tightening toggle bolts and wood
screw, make sure the bottom of the mounting plate
touch the bottom of the cabinet when pushed
flush against the wall and that the plate is properly
centered under the cabinet.
CAUTION:
Be careful to avoid pinching fingers
between the back of the mounting plate and the wall.
Tighten all bolts. Pull the plate away from the wall
to help tighten the bolts.
3
4
ATTACH THE MOUNTING
PLATE TO THE WALL
A1.
Attach the plate to the wall using toggle bolts.
At least one wood screw must be used to attach
the plate to a wall stud.
Remove the toggle wings from the bolts.
Insert the bolts into the mounting plate
through the holes designated to go into drywall
and reattach the toggle wings to
3
⁄
4
″
(19 mm) onto
each bolt.
1
INSTALLATION OVERVIEW
A1.
Attach Mounting Plate to Wall
A2.
Prepare Top Cabinet
Mount Microwave Oven
A5.
Adjust Exhaust Adaptor
A6.
Wall
Mounting
Plate
Spacing for Toggles
More Than Wall
Thickness
Bolt End
Toggle
Bolt
Toggle Wings
To use toggle bolts:
Installation Instructions
2
OUTSIDE TOP EXHAUST
(Vertical Duct)
A
IMPORTANT NOTES:
•
Make sure the screws for the
blower motor and blower plate
are securely tightened when
they are reinstalled. This will
help to prevent excessive
vibration.
•
Make sure the motor wiring has
been properly routed and secured,
and that the wires are not pinched.
A7.
Connect Ductwork
A3.
A4.
Check Damper Operation
Adapting Microwave Blower for
Outside Top Exhaust
12"
4"
NOTE: IT IS VERY I
MPORTANT TO
READ AND FOLLO
W THE DIRECTION
S
IN THE INSTALLAT
ION INSTRUCTION
S
BEFORE PROCEEDING
WITH THIS
REAR WALL TEMPLA
TE.
This Rear Wall Templ
ate serves to position th
e bottom
mounting plate and to l
ocate the horizontal e
xhaust
outlet.
1. Use a level to chec
k that the template is p
ositioned
accurately.
2. Locate and mark at lea
st one stud on the left o
r
right side of the cente
rline.
016'
It is important to use a
t least one wood
screw mounted firmly i
n a stud to support the w
eight
of the microwave. Mar
k two additional, even
ly spaced
locations for the suppl
ied toggle bolts.
3. Drill holes in the mar
ked locations. Where t
here is
a stud, drill a 3/16" h
ole for wood screws. F
or holes
that do not line up w
ith a stud, drill 5/8" ho
les for
toggle bolts.
016'
DO NOT INSTALL THE
MOUNTING PLATE
AT THIS TIME.
4. Remove the templa
te from the rear wall.
5. Review the Installati
on Instruction book for
your
installation situation
.
Locate and mark holes
to align with holes in t
he
mounting plate.
IMPORTANT:
LOCATE AT LEAST
ONE STUD ON EIT
HER SIDE OF
THE CENTERLINE.
MARK THE LOCATION
FOR 2 ADDITIONA
L, EVENLY
SPACED TOGGLE BO
LTS IN THE MOUN
TING PLATE
AREA.
Trim the rear wall tem
plate along the dott
ed line.
Darle vuelta a la hoja
para consultar la
versión en Español.
Locate and mark holes
to align with holes in t
he
mounting plate.
IMPORTANT:
LOCATE AT LEAST O
NE STUD ON EITHER SI
DE OF
THE CENTERLINE.
MARK THE LOCATIO
N FOR 2 ADDITION
AL, EVENLY
SPACED TOGGLE BO
LTS IN THE MOUN
TING PLATE
AREA.
Trim the rear wall t
emplate along the dotted lin
e.
3/8" TO EDGE
EN-12
