background image

10

Cleaning the Conveyor Belt Tensioning Station

The tensioning station must be cleaned once a month, 

or as needed to maintain optimal performance.

1. Switch off the shredder and unplug from wall outlet.

2. Remove the feed table and front panel of tensioning

station (Fig. 2).

3. Remove particles and dirt.

4. Re-install the feed table and front panel of

tensioning station.

Tensioning station adjuster

Fig. 2

Checking the Cutting Head Chain Tension

Check the chain tension once every week in the first month, then once a month thereafter. 

1. Switch off the shredder and unplug from wall outlet.

2. Remove the top right side cover.

3. The sagging of the chain (see Fig. 3) should be 9 - 14 mm, measured from the top inside of

the frame to the cutting head chain.

If it is not within this range, loosen the tension screws until the sagging reaches the 

correct level. Retighten the tension nuts.

4. Replace the side cover, plug in the shredder.

NOTE:

Excessive tensioning of the chain can cause premature wear of the chain and bearings. 

The smallest allowed chain sagging in the first month of operation is 5 mm. After that, 9 mm.

Fig. 3

Underside View of Feed Table

and Infeed Conveyor

MyBinding.com

5500 NE Moore Court 

Hillsboro, OR 97124 

Toll Free: 1-800-944-4573 

Local: 503-640-5920

Содержание FD 8906CC Cross-Cut















Отзывы: