background image

PRE-DRILL 

WITH 2MM BIT 

FOR ALL STEPS 

BELOW.

PRE-DRILL 

WITH 2MM BIT 

FOR ALL STEPS 

BELOW.

PRE-DRILL 

WITH 2MM BIT 

FOR ALL STEPS 

BELOW.

60

MM

SCREWS

60

MM

SCREWS

60

MM

SCREWS

60

MM

SCREWS

60

MM

SCREWS

5

1a

FLOOR & PANEL LAYOUT

1c

APEX SECTIONS

1b

SIDE PANELS 

Position your floor

 in your desired location.

Layout the panels

 around your shed base.

We recommend to start in a back corner then 

work from the back panels to the front 

panels for assembly. 

Attach the first Apex Section

 to the back 

panels by screwing to the wall panels as shown 

below.

Attach the other Apex Section

 to the front 

panels by screwing to the wall panels as shown 

below.

Start at a back corner.

 See the section layout 

on page 4 to confirm position. Secure the 

corner as shown below. 

Repeat the process for the remaining panels 

and 

secure

 the 

panels together.

 Make sure 

that the bottom frame of the wall panel rests 

on the outer edge of the floor.

Secure the panels into place by 

screwing into 

the floor bearers.

 Use 3 x screws for the larger 

panels and 1 x screw for the smaller panels as 

shown in the bottom visual.

EG. INSIDE CORNER

SIDE PANEL

BACK PANEL

EG. SIDE PANELS

APEX SECTION

EG. INTO FLOOR BEARERS

APEX SECTION

Содержание Timberdale 4 x 6 ft Tongue & Groove Shed










Отзывы: