3’ x 5' Value Shed
Important :
Assembly of this
shed requires a
minimum of two
adults.
MUST PRE DRILL
Issue 0114
FELT
K
VOL35PE
PLAIN END
VOL35PS
PLAIN PANEL
Qty 2
15406108
ROOF BOARD
Qty 2
85052
QTY 1
C
I
F
J
E
9090012FINDTR
FINIAL
Qty 2
H
VOL35 PARTS LIST
1
5X3SHEDFL
FLOOR
DR665X1590
DOOR
40080590DTR
BARGE BOARD 590mm Qty 4
Place the turn button
against the door end
approximately half way
up. Make sure that it is
positioned in line with
the framing on the
reverse and close
enough that it will hold
the door shut when
turned.
Fix using a 30mm
(black) screw.
REQUIRED TOOLS :
(NOT SUPPLIED)
POZI DRIVE SCREWDRIVER
SPIRIT LEVEL
TAPE MEASURE
SHARP KNIFE
FOR ROOFING FELT
HAMMER
Fixing Pack (VOL35FP)
Not to Scale
Turn Button
L’ bracket
Qty 4
30mm Screw Qty 22
60mm Screw Qty 2
8mm Felt tacks
Qty 60
4
E
IMPORTANT, RETAIN FOR FUTURE REFERENCE;
READ CAREFULLY
Check all parts prior to assembly
This building is pre-treated with a factory base coat for
protection during storage and transit. We recommend that
you treat your new building as soon as possible after
assembly using a wood preservative treatment. Apply in
accordance with the manufacturers instructions.
- Timber is a natural material. It will shrink and swell as a
result of varying moisture content.
- Please keep all plastic bags and small parts away from
children
- This product must be built on a solid level base.
- The roof of this product is not a load bearing structure.
Technical Help line:
0333 321 3142
8.30
am
to 5.00
pm Monday to Friday.
In line with your statutory rights, please check all parts
prior to assembly, as assembly of damaged parts may be
deemed to be acceptance and this may affect the
remedies you are entitled to. If the product is not
constructed in accordance with the instructions, or is
altered in anyway (e.g. painted), the manufacturer cannot
be held liable for any resulting damage.
Place and secure two hinges to the door so that they line
up with the battens on the reverse using 4x30mm (black)
screws for each.
Place the door into the door end ensuring that it is square.
Fix the doors in place using 3x30mm (black) screws for the
other section of each hinge.
50mm Screw Qty 13
Tee Hinge
Qty 2
Place the corner strips so that they
cover the joins between the panels. Fix
each in place using 3 x 25mm screws.
2
30mm Screw (Black) Qty 15
25mm Screw Qty 48
Place the panels on top of the floor. Make sure that all the panels are tight and flush before fixing them to
each other using 3x50mm screws.
When the panels are secured to each other, ensure that they are square before securing them to the floor.
Secure the door end to the floor using 1 x 50mm screws making sure it locates into the floor bearer. Fix the
plain sides to the floor using the L’ brackets. Position these side ways and make sure they are in line with the
floor bearers underneath. Fix each in place using 4 x 25mm screws.
VOL35DE
DOOR END
40121600DTR
CORNER STRIP 40x12x1600mm Qty 4
28281540
BATTEN 28x28x1540mm Qty 2
45281506PAR
BATTEN 45x28x1506mm Qty 1
A
D
G
B
A
A
Place the 1506mm batten so that it sits
on the framework at the apex of both
the plain end and door end as shown.
Fix this in place using 1 x 60mm screw
for each end. (Make sure you pre-drill).
A
C
A
I
3
A
B
A
C
A
H
50mm screw
