background image

 

Document Information 

 Page 6 of 31 

FSS JODY-W263 Integration Instructions Rev 02.docx 
 

www.foresightsports.com 

 10 

OFDM 

20 MHz 

6, 9, 12, 18, 24, 36, 48, 54 Mbps 

16 dBm 

11 

OFDM 

20 MHz 

6, 9, 12, 18, 24, 36, 48, 54 Mbps 

11 dBm 

OFDM 

20 MHz 

HT20 MCS0-MCS7 

11 dBm 

 10 

OFDM 

20 MHz 

HT20 MCS0-MCS7 

16 dBm 

11 

OFDM 

20 MHz 

HT20 MCS0-MCS7 

11 dBm 

OFDM 

40 MHz 

HT40 MCS0-MCS7 

11 dBm 

 8 

OFDM 

40 MHz 

HT40 MCS0-MCS7 

16 dBm 

OFDM 

40 MHz 

HT40 MCS0-MCS7 

11 dBm 

Table 1: Wi-Fi power table for operation in the 2.4 GHz band 

Wi-Fi Output power for 5 GHz band 

Channel 

Modulation 

Channel  
bandwidth 

Data rates 

Maximum power 
setting 

36 - 64 

OFDM 

20 MHz 

6, 9, 12, 18, 24, 36, 48, 54 Mbps 

15 dBm 

36 - 64 

OFDM 

20 MHz 

HT20 MCS0-MCS7 

15 dBm 

36 - 64 

OFDM 

20 MHz 

VHT20 MCS0-MCS8 

15 dBm 

38 - 62 

OFDM 

40 MHz 

HT40 MCS0-MCS7 

15 dBm 

38 - 62 

OFDM 

40 MHz 

VHT40 MCS0-MCS9 

15 dBm 

42 

OFDM 

80 MHz 

VHT80 MCS0-MCS9 

14 dBm 

Table 2: Wi-Fi power table for operation in the 5 GHz U-NII-1 and U-NII-2A bands

 

Channel 

Modulation 

Channel  
bandwidth 

Data rates 

Maximum power 
setting 

100 - 144 

OFDM 

20 MHz  

6, 9, 12, 18, 24, 36, 48, 54 Mbps 

15 dBm 

100 - 144 

OFDM 

20 MHz  

HT20 MCS0-MCS7 

15 dBm 

100 - 144 

OFDM 

20 MHz  

VHT20 MCS0-MCS8 

15 dBm 

102 

OFDM 

40 MHz  

HT40 MCS0-MCS7 

14 dBm 

102 

OFDM 

40 MHz  

VHT40 MCS0-MCS9 

14 dBm 

110-142 

OFDM 

40 MHz  

HT40 MCS0-MCS7 

15 dBm 

110-142 

OFDM 

40 MHz  

VHT40 MCS0-MCS9 

15 dBm 

106 - 138 

OFDM 

80 MHz 

VHT80 MCS0-MCS9 

14 dBm 

Table 3: Wi-Fi power table for operation in the 5 GHz U-NII-2e band 

Channel 

Modulation 

Channel  
bandwidth 

Data rates 

Maximum power 
setting 

149 - 165 

 OFDM 

20 MHz  

6, 9, 12, 18, 24, 36, 48, 54 Mbps 

15 dBm 

149 - 165 

 OFDM 

20 MHz  

HT20 MCS0-MCS7 

15 dBm 

149 - 165 

 OFDM 

20 MHz  

VHT20 MCS0-MCS8 

15 dBm 

151 

 159 

 OFDM 

40 MHz 

HT40 MCS0-MCS7 

15 dBm 

151 

 159 

 OFDM 

40 MHz 

VHT40 MCS0-MCS9 

15 dBm 

155 

 OFDM 

80 MHz 

VHT80 MCS0-MCS9 

14 dBm 

Table 4: Wi-Fi power table for operation in the 5 GHz U-NII-3 band 

2.2 

Co-location 

If the module is to be co-located with another transmitter, additional measurements for 
simultaneous transmission are required. The results must be added to the grant file as a Class II 
Permissive Change.  

The module is not currently approved for co-location with any other modules. 

Содержание JODY-W263
































Отзывы: