FOREDOM M.BL Скачать руководство пользователя страница 3

FOREDOM

®

Form 1248    3/08  n

Printed in USA

The Foredom Electric Company

Bethel, CT USA 06801

www.foredom.com

Maintenance

Lubrication: 

The Foredom Bench Lathe has pre-lubricated ball bearings and a dust-proof

motor housing and does not require any lubrication. The motor is designed to operate
above room temperature which will be warm to the touch but will not harm the motor.

Brush Wear: 

Disconnect power cord before checking for brush wear. Check for brush

wear periodically (about every 200 hours of continuous operation). Unscrew the brush tube
caps, check the brush length, and install new brushes if the old ones are less then 3/16

(4.7mm) in overall length. Be sure that the radius in the end of the brush is in line and 
conforms to the commutator surface. Replacement brushes (MP 262 P) are available from
your dealer, the factory, or you may order them online from 

www.foredom.com

.

Repair Service

Factory repairs are done promptly and at reasonable cost. If you wish, you can send your
equipment directly to the factory marked Attention: Repair Dept. Be sure to give your street
address and telephone number. The equipment should be accompanied by 
a brief note describing the problem. Estimates will be made upon request.

Owner's Registration Card

Send your Owner's Registration Card to Foredom right away. We will keep your card

in our Owner's Registration File.

Bench Lathe Attachments

Tapered Spindles

A-TM5 Left Hand

A-TM6 Right Hand

Precision, true running tapered spindles suitable for
speeds up to 7,000 RPM. Fits 5/16

(8mm) diameter

straight motor shafts. Double locking screws.
Suitable for use with cotton, felt, and chamois buffs
with shellac-hardened leather, or lead centers. Also
used with felt inside ring buffs on wooden mandrels.

Use A-TM5 on left side (as you face it) and 
A-TM6 on right side of bench lathe.

S.BO-516N Flexade

®

Comes with 5/16

″ 

(8mm) coupling and extra flexible

30

long neoprene sheath allows you to use any of

Foredom’s interchangeable handpieces. 

Must be

attached to the right side of the lathe. Handpiece
not included.

Wheel Mandrels

A-WM-5 Left Hand         A-WM-6 Right Hand

Mandrels to hold rubber bonded abrasive wheels, 
sanding drums, brushes, and other accessories with 
1/4

mounting holes and rated for maximum speeds 

of 7,000 RPM or higher. Fits 5/16

(8mm) diameter

straight motor shafts.

LIMITED WARRANTY

The Foredom Electric Co. warrants the Bench Lathe to be free of defects in material or 
workmanship for a period of 1 year after purchase. During the warranty period, the defective 
product will be repaired or replaced without charge or, at our option, the purchase price will be
refunded. This warranty does not cover damage caused in transit or by accident, misuse, or 
ordinary wear. 

ALL IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED  TO WARRANTIES OF 
FITNESS AND MERCHANTABILITY, ARE HEREBY LIMITED IN DURATION TO A PERIOD
ENDING ONE YEAR FROM DATE OF PURCHASE, AND WE WILL NOT BE LIABLE OR
RESPONSIBLE FOR ANY SPECIAL OR CONSEQUENTIAL DAMAGES.
Repair or replacement will be made at our option if the product is returned post-paid to:

The Foredom Electric Company

16 Stony Hill Road

Bethel, CT 06801 USA

All warranty repairs must be done at the factory at the above address. We will not pay any 
shipping or transportation charges. This warranty only covers the original purchaser of the 
product. Some states do not allow limitations on how long an implied warranty lasts, so the above
limitations may not apply to you. This warranty gives you specific legal rights, and you may also
have other rights which vary from state to state.

A-CHA-5 Collet Holder

Collet holder on arbor for 5/16

diameter motor shafts. Comes
with 3/32

, 1/8

, and 1/4

″ 

collet,

pin and wrench. For use with all
440 series collets in 1/16

to

1/4

and metric sizes. 

Use on

right side only.

MADCH-1 Dust Collector Hoods

Heavy gauge sheet metal construction 
with non-skid pads on the bottom. 
2

1

⁄2

(64mm) adapter fits most dust 

collection system hoses. 

Height: 6

1

⁄2

″ 

(165mm) 

Width: 4

5

⁄8

″ 

(117mm) 

Depth: 8

5

⁄8

″ 

(219mm) deep

440 Series collets

P/N

Nominal cap.

HP441

1/16

HP442

3/32

″ 

(2.3mm)

HP443

1/8

HP444

5/32

HP445

3/16

HP447

1/4

HP448

3mm

HP449

6mm

A-JCA-2 
Chuck Arbor

Arbor for 5/16

diameter motor shafts adjusts to

hold accessories from 0– 5/32

(3.9mm). Comes

with key in molded plastic handle.

Use on right side only.

If this manual has been downloaded or received as a replacement to go with an 
older model (made prior to 2003), the attachments shown in this manual will not fit.
Older bench lathes require attachments that will fit 1/4

(6.35mm) straight motor shafts.

Contact your Foredom dealer or Foredom for bench lathe attachments.

Side of        Arbor Hole

Part No.   Lathe

Diameter

A-4561

Right hand

3/8

A-4562

Left hand

3/8

A-4568

Both

1

Tapered Spindle Adapters 

for Scotch-Brite

Radial Bristle Discs

FX Wheel Adapter for 3M

FX Polishing Wheels

Отзывы: