Ford M-6007-Z427AFT Скачать руководство пользователя | Manualshive

Страница: 12 / 19

background image

M-6007-Z427AFT/ART
Crate Engine
INSTALLATION INSTRUCTIONS

NO PART OF THIS DOCUMENT MAY BE REPRODUCED WITHOUT PRIOR AGREEMENT AND WRITTEN PERMISSION OF

FORD RACING PERFORMANCE PARTS.

Techline 1-800-367-3788

Page 12 of 19

IS-1850-0387

Factory Ford shop manuals are available from Helm Publications, 1-800-782-4356

INTAKE MANIFOLD INSTALLATION INSTRUCTIONS FOR FORD RACING CRATE LONG BLOCKS

! ! ! PLEASE READ ALL OF THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION.

AT ANY TIME YOU DO NOT UNDERSTAND THE INSTRUCTIONS, PLEASE CALL THE FORD RACING

TECHLINE AT 1-800-367-3788 ! ! !

Below is a picture of everything needed to accomplish the installation.

•

M-9439-A50 intake gaskets, these are included with your crate engine

NOTE: Cork end rail gaskets are not used

•

(12) Intake manifold bolts 5/16-18 UNC grade 8, with flat washers

•

Torque wrench

•

Motorcraft TA-29 silicone or equivalent RTV high temperature silicone sealer

•

6” Ruler and set of feeler gauges

•

Surface cleaner (Brake Cleaner) or lacquer thinner (not pictured)

•

A gasket sealer/contact cement: such as Gasgacynch®, High Tack® or Indianhead®

«
...
10
11
12
13
14
...
»

Содержание M-6007-Z427AFT




















Отзывы:

Нет отзывов

Похожие инструкции для M-6007-Z427AFT

Бренд: Wartsila Страницы: 168

ALCYO ACCU-TRK-AT

Бренд: Oben Страницы: 28

Бренд: Vedeneyev Страницы: 381

5.7L Corvette 2004

Бренд: Chevrolet Страницы: 1000

Бренд: Pentair Страницы: 110

Бренд: HARTFORD Страницы: 70

Бренд: Daewoo Страницы: 188

Бренд: Volvo Страницы: 8

Бренд: DANA Страницы: 3

Бренд: DANA Страницы: 3

Бренд: DANA Страницы: 3

Бренд: DANA Страницы: 3

Бренд: DANA Страницы: 3

Бренд: DANA Страницы: 3

Бренд: O.S. engine Страницы: 4

BREVINI V Series

Бренд: DANA Страницы: 34

Бренд: Stiga Страницы: 40

Бренд: D-MOTOR Страницы: 50

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды