Ford M-6007-XEFMS Скачать руководство пользователя

Страница: 13 / 13

M-6007-XEFMS
340 HP Crate Engine
GUIDE

NO PART OF THIS DOCUMENT MAY BE REPRODUCED WITHOUT PRIOR AGREEMENT AND WRITTEN PERMISSION OF

FORD RACING PERFORMANCE PARTS.

Techline 1-800-367-3788

Page 13 of 13

IS-1850-0290

Factory Ford shop manuals are available from Helm Publications, 1-800-782-4356

•

The damper assembly M-6316-D302 (neutral balance) may require a spacer for pulley alignment.

•

The flywheel included M-6375-D302 should work for most 157-tooth manual transmission applications. For other
transmission applications, use the proper neutral balance flywheel.

•

Firing order 1-3-7-2-6-5-4-8 (5.0L HO and 351W order).

•

Built with current available parts. Photo and specs may vary.

•

Shipping weight approximately 425 lbs.

QUICK INFO

•

Intake bolt torque: 16 to 18 ft-lb in 3 steps

•

Oil: 5 qts 10W30 or 10W40

•

Timing: 14 to 16 degrees initial, 36 to 38 total with carburetion. 14 to 16 initial with factory EFI

•

Fuel delivery: 600 cfm carburetor, 30 lb injectors EFI

•

Distributor gear: steel

•

Crank pulley spacer: M-8510-D351 recommended for most 4-bolt pulley applications

Содержание M-6007-XEFMS














Результаты поиска

Содержание M-6007-XEFMS

Отзывы:

Похожие инструкции для M-6007-XEFMS

Бренды по названию

Популярные бренды

Ford M-6007-XEFMS, Руководство пользователя

Результаты поиска

Содержание M-6007-XEFMS

Отзывы:

Похожие инструкции для M-6007-XEFMS

Бренды по названию

Популярные бренды