Ford 2009 Taurus X Скачать руководство пользователя страница 111

Страница: 111 / 336

Erasing HomeLink

姞

buttons

To erase the three programmed
buttons (individual buttons cannot
be erased):

•

Press and hold the two outer
HomeLink

威

buttons until the

indicator light begins to
flash-after 20 seconds. Release
both buttons. Do not hold for
longer that 30 seconds.

HomeLink

威

is now in the train (or learning) mode and can be

programmed at any time beginning with Step 1 in the

Programming

section.

Reprogramming a single HomeLink

姞

button

To program a device to HomeLink

威

using a HomeLink

威

button previously

trained, follow these steps:
1. Press and hold the desired HomeLink

威

button.

Do NOT

release the

button.
2. The indicator light will begin to flash after 20 seconds. Without
releasing the HomeLink

威

button, follow Step 1 in the

Programming

section.
For questions or comments, contact HomeLink

威

www.homelink.com

1–800–355–3515.

MESSAGE CENTER

With the ignition on, the message
center, located on your instrument
cluster, displays important vehicle
information

through a constant

monitor of vehicle systems.

You

may select display features on the
message center for a display of status. The system will also notify you of
potential vehicle problems with a display of system warnings followed by
a long indicator chime.

Selectable features

Reset

Press this control to select and reset functions shown in the INFO menu
and SETUP menu.

2009 Taurus

(500)

Owners Guide, 1st Printing
USA

(fus)

Driver Controls

111

Содержание 2009 Taurus X

















































































































































































































































































































































Результаты поиска

Содержание 2009 Taurus X

Отзывы:

Похожие инструкции для 2009 Taurus X

Бренды по названию

Популярные бренды

Ford 2009 Taurus X, Руководство пользователя

Результаты поиска

Содержание 2009 Taurus X

Отзывы:

Похожие инструкции для 2009 Taurus X

Бренды по названию

Популярные бренды