Force 12 Sigma-280 Magnum Скачать руководство пользователя страница 10

DW-Manual-Sigma-280 Magnum-001   FORCE 12  SIGMA-280Magnum Assembly Instructions   Page  10   of   32 

 

 

 

_____a) 

Slide both covers over the coils. 

_____b) 

Slide the end caps over both of the covers, being sure not to disturb the coil 
spacing. 

_____c) 

If the cover drain holes were not drilled earlier, drill four (4) drain holes in a 
straight line in what will be the bottom of the coil covers. Use a 1/8” or 3/16” 
drill bit. 

_____d) 

Rotate the drain holes so that they are down. 

_____e) 

Use a good quality silicone sealant (RTV) and run a bead along the caps in 
two (2) places: 

 

_____e1. 

Around the hole where the element goes through each cap 

 

_____e2. 

Around each cap where the cover enters the cap. 

_____f) 

The caps and covers can be painted if desired. 

 
_____24) 

The driver is tuned next. 

 
_____25) 

Be sure the relay boxes on both elements are operating in tandem. 

 
_____26) 

Using the same basic procedure as on the reflector, tune the driver. 

 
_____27) 

Attach the actual balun, feed line and matching hairpin to the driver feed point on the relay 

box. 

 

_____a) 

Set the initial spacing on the hairpin coil about ¾” between turns. 

 
_____28) 

Energize the CW/Phone relays for LOW PHONE. 

 
_____29) 

Tune the coils on the driver for a frequency of 3.790-3.795 and secure the far ends as before, 

then secure the coil covers. 

 
_____30) 

Adjust the hairpin match for the lowest VSWR. 

 
_____31) 

Open the CW/Phone relay and adjust the coils on the relay for the operating frequency (i.e. 

3505). 

 

_____a) 

Secure the cover on the relay box. 

 
_____32) 

Secure the coils in position, if not done so already. 
_____a) 

Be sure the U-bolt is tight and the coil is in position for proper tuning. 

_____b) 

Use a ¼” drill and drill through the tip end of the coil (flattened end) and 
through the element. 

_____c) 

Use a ¼ - 20 bolt and ny-loc to secure the coil. 

 
_____33) 

Secure the covers. 

 

 

_____a) 

Slide both covers over the coils. 

_____b) 

Slide the end caps over both of the covers, being sure not to disturb the coil 
spacing. 

_____c) 

If the cover drain holes were not drilled earlier, drill four (4) drain holes in a 
straight line in what will be the bottom of the coil covers. Use a 1/8” or 3/16” 
drill bit. 

_____d) 

Rotate the drain holes so that they are down. 

Содержание Sigma-280 Magnum





















Отзывы: