Forbes Marshall FMSTR34 Скачать руководство пользователя страница 9

4. 

Product Working Principle:

 

Forbes Marshall Cast Strainer is used to remove dirt, debris and other foreign particles from the 
fluid, it restrict the particle size which are larger than specified sieve size (mesh or perforation). 
Pressure drop across the strainer will increase as dirt and debris will block the opening of the sieve. 
As pressure drop increases above certain specified limit the strainer sieve need to be cleaned. 

5.

 

Installation Guidelines : [Refer Figure 3 and 4]

 

 

 

Note

: Before implementing any installations observe the 'Important Safety notes” in 

section 2. Referring to the Installation and Maintenance Instructions, name-plate and 
Technical  Information  Sheet,  check  that  the  product  is  suitable  for  the  intended 
installation.

1. 

Check the direction marked on the strainer and the direction of fluid flow.

2. 

Remove protective covers from connections.

3. 

Strainer can be fitted on steam /gases and liquid systems in either horizontal pipework or 

vertical pipework when the flow and strainer pocket pointing downward. In a horizontal 
pipeline on steam / gas system the strainer pocket should be in the horizontal plane as this 
reduces the possibility of water hammer because of condense steam get accumulated in  
screen when strainer pocket   pointed downward. On liquid systems the strainer pocket 
should point downwards. 

4. 

Suitable isolation valves must be installed to allow for safe maintenance.

 

Note: 

Never install strainer in vertical pipework with flow from bottom to top it can lead to 

re-entrainment of filtered dirt or foreign particles back into the incoming flow.

5. 

Strainer can be lagged (insulated) if required.

Figure 3 : Strainer installation on horizontal pipework

Figure 4 : Strainer installation on vertical pipework

6.

 

Start-up and Commissioning:

 

6.1.  Flushing of lines:

 

 

As  part  of  pre-installation  all  fluid  handling  equipment  particularly  piping  should  be 

thoroughly cleaned of scale and the internal debris which accumulates during construction. 
This  is  accomplished  by  blowing  or  flushing  with  air,  steam,  water  and  other  suitable 

Strainer installed on steam or gas line

Strainer installed on liquid line

Flow downwards

Flow upwards

7

FMSTR34, FMSTR54, FMSTR54#600

Содержание FMSTR34

















Отзывы: