background image

 

 

4b. 

Mount the control box on the wall. Drill two 1/8" 

(3mm) holes as shown, and push drywall anchors 

into each hole. Secure the control box to the wall 

with the drywall screws.

5. Connect The Sensor Cable

Plug the sensor cable from the faucet into the 

control box to activate the infrared sensor.

6. Water Pipe Connections

Connect the incoming water supply line to the 

control box, at the connection marked Inlet. Thread 

on the swivel nut to the hose by hand. Tighten with 

a wrench.

Connect the faucet hose to the control box, at the 

connection marked Outlet.

Water Supply

Outlet

Water Supply

Inlet

Please wait approximately 60 seconds after 

connecting the sensor cable for sensor calibration to 

complete and to begin using the faucet.

or

  Temp. Control Thermostatic Mixer

Many automatic faucets do not have hot & cold 

handles to adjust the water temperature coming 

out of the spout, and normally installed to a single 

water supply only. This valve is used for automatic 

faucet to mix hot and cold water and to control 

water temperature. Normally it would be mounted 

under the sink with required temperature set.

Working Pressure: 0.05MPa-0.5MPa

Cold Water Temp: 0°C

Hot Water Temp: 85°C

Outlet Flow Rate: 20m

3

/h

Cold Water in

NPS male G1/2

Mixer Water out

NPS female G1/2

Hot Water in

NPS male G1/2

Fontana Sensor Faucets

©

Fontana Sensor Faucet

Customer Service: 800-684-4489

fontanasensorfaucets.com

4

Содержание FS-509AB








Отзывы: