background image

 

Page 15 sur 15 

 

12. WARRANTY 

ISE Metal inc. warrants that the stop logs it manufactures and delivers to the Buyer are free from defects 
in  material,  workmanship  and  fabrication  for  a  period  of  60  months  from  the  date  of  receipt  of  the 
equipment at their installation location.  To benefit from this warranty, the  Buyer shall promptly report in 
writing  any  failure  during  the  warranty  period.   Provided  that  the  buyer  has  stored,  installed,  maintained 
and used the equipment in a workmanlike manner and has complied with the manufacturer’s  instructions 
and  recommendations  put  forth  in  the  Installation,  Operation  and  Maintenance  Manual,  at  its  discretion, 
ISE Metal will either correct the defect at its factory or provide the required parts. Shipping costs from the 
factory  to  the  installation  site  and/or  labor  on  the  equipment  installation  site  are  not  covered  by  this 
warranty.   Accessories  and  equipment  supplied  by  ISE  Metal  inc.  with  the  gates,  but  manufactured  by 
others will be protected by the warranty offered to ISE Metal by the manufacturers of the equipment which 
are  transferable  to  Buyer.   ISE  Metal  inc.  will  not  be  held  responsible  for  any  direct,  indirect, 
consequential, contingent or incidental damages, repairs, replacements or other fixes and adjustments to 
the equipment nor any labor costs incurred by the Buyer or its subcontractors or others without the prior 
written  consent  of  ISE  Metal  Inc.   The  effects  of  corrosion,  erosion  and  normal  wear  and  tear  are 
specifically excluded from this warranty. The Buyer shall not use equipment that is considered defective 
without first obtaining a written consent of ISE Metal inc., otherwise the Buyer uses the equipment at their 
own risk and responsibility. 
 
ISE Metal Inc. provides no other warranty or makes no other express or implied representation and any 
implied warranty of fitness for a particular purpose is declared non-existent. 
 
Corrections  by  ISE  Metal  inc.  of  non-compliance  described  above  constitute  complete  fulfillment  of  its 
responsibility in this manner. 
 

13. CONTACT FONTAINE AQUANOX 

 
If needed, Fontaine-Aquanox can be contacted with the following methods: 
 
Web site:  http://www.ISEAquanox.com 
Phone:  (819) 769-0157    or toll free: 1-855-769-0157 
Mailing address:   20 route de Windsor, Sherbrooke (Quebec), Canada, J1C 0E5 
 
 

Содержание 98 Series
















Отзывы: