background image

7

GB

5

5

5

5

5

  ASSEMBLY OF THE DETERGENT

SPRAYING DEVICE 

(Fig.

10

)

- Insert the sprayer pipe into the spray gun

- Rotate the pipe by 90°, and on extracting it, click it in.

 4

 4

 4

 4

 4

 CONNECTION OF THE WATER SUPPLY
PIPE

 9

 9

 9

 9

 9

 EQUIPMENT

The nozzle with rotating head can be rotated in a
continuous manner, by moving the terminal part.

ADDITION OF DETERGENT

The detergents must not be
allowed to dry on the object to
be cleaned.

- Push the sprayer pipe towards the gun, turning it

by 90° and then extract it (Fig. 

14

)

- Apply the detergent spray kit to the gun (Fig. 

15

).

- Fill the container of the spray kit with suitable

detergent (see paragraph “General safety
recommendations” in this booklet).

 8

 8

 8

 8

 8

 SWITCHING OFF THE MACHINE

- Press the button marked with an

 

0

0

0

0

0

 on the switch

(Fig. 

11- 

OFF

OFF

OFF

OFF

OFF

)

- Turn off water supply tap.

-    Actuate spray gun until water drips from the

nozzle (machine is now de-pressurized).

- Release trigger.

- Press safety latch on spray gun. (Fig.

13

- pos.

1

).

The spray gun is locked and cannot be actuated
accidentally.

- Unplug machine from socket outlet.
- Disconnect water supply hose from machine and

water supply mains.

 7

 7

 7

 7

 7

 APPLIANCE ACTIVATION

- Press button 

(Fig.

11

-ON) on the main switch

positioned at the rear of the device

-

Position the spray gun on the object to

be cleaned - never on people !

- Press the safety device (Fig. 

12

 - pos. 

1

) - the gun

is released

- Direct the nozzle downwards

- Fully press down the trigger (Fig.

 12

 - pos. 

2

)

  6

  6

  6

  6

  6

 ELECTRICAL CONNECTION OF THE

APPLIANCE

The mains voltage must match the operating voltage.
(See identification plate)

- Insert the plug into a power socket  installed in

compliance with regulations.

Check the minimum section of the individual cables
using extensions.

Position the extensions so as to maintain the protection
class of the equipment.

Voltage V

Cable

Cross-section

length

mmm2

   230

up to 2

   1,5

   230

20 to 5

   2,5

Connect a clean water supply pipe (Fig. 

9

– pos.

3

) to the water mains, checking to

ensure that the minimum pressure is of 1.5
bar and maximum is of 6 bar, with a
minimum flow rate of 6 l per min.

- Connect the water supply pipe (min. diam ½”) to

the water mains (fig.

8

)

- Fit the click-on attachment (Fig. 

9

 - pos.

1-3

) onto

the fitting (

2

);

GB

It is advisable to point out the correspondence of the
holes: remove the machine from the bracket and
make the holes in such a way as to conveniently
work with the drill.

After definitely fixing the machine to the wall, intro-
duce the high pressure pipe into the loop under the
pipe winding device (Fig. 

5

); then fix the holder

bracket for accessoiries as shown in fig. 

6

.

Connect the high pressure pipe (previously released)
to the gun and make sure that the safety device is
locked (Fig. 

7-A

).

Содержание 840










Отзывы: