Follett E15CI100A Скачать руководство пользователя

Страница: 12 / 44

Dispenser and Ice Machine 230 V/50 Hz, Rear Drain

Cleaning and Sanitizing Procedure

(continued)

User Interface and Exterior Cabinet

1 . Press and release maintenance/clean switch so that only "ICE" displays in the user interface to enter

Cleaning Mode (and disable dispensing) .

2 . Plastic parts, including the user interface, can be cleaned with a non-abrasive glass cleaner . Clean

stainless steel panels with stainless steel cleaner .

3 . Press and release maintenance/clean switch to put unit back into service .

Service

LED Indicator Description

The LED Indicator is located behind the front panel .

Fig . 8

Clean

Drip tray

ater leak

HI press

HI amps

Service

Maint

Low water

Time delay

Sleep cycle

Making ice

Low bin

Power ON

LED Name

LED Color

Description

Clean

Green

The dispenser is in Cleaning Mode . Dispenser is disabled to allow for cleaning of front panel .

See

Maintenance/Cleaning Mode on page 9

—

N/A

Not used .

Red

Six-month periodic maintenance required .

Drip tray

Red

Drip tray full .

Water leak

Red

Internal leak in dispenser .

High amps

Red

Auger gearmotor has exceeded 0 .55A . The HI amps and Time delay LEDs will illuminate,

the machine will shut down for one hour, the LEDs will turn off, and the machine will resume

normal operation .

Service

Red

8000 hour bushing check (call Follett technical service group at (877) 612-5086 or
+1 (610) 252-7301) .

Maintenance

Yellow

Enter Maintenance Mode by pressing and holding maintenance/clean switch for 5 seconds .

Unit will not make or dispense ice .

Low water

Yellow

Insufficient water supply to machine or no low bin LED upon startup .

Time delay

Yellow

Ice production will not resume for at least 15 minutes after a full bin is achieved and a

minimum amount of dispense activity has elapsed .

Sleep cycle

Green

After a full bin and 10 minutes of non-use, the unit goes into standby and will not produce ice

until either:

E7 Series:12 hours has elapsed, E15 Series: 4 hours has elapsed

or ice has dispensed .

Making ice

Green

Gearmotor, compressor, and fan motor energized .

Low bin

Green

Bin switch closed calling for ice .

Power on

Green

Power supplied to unit .

Содержание E15CI100A













































Результаты поиска

Содержание E15CI100A

Отзывы:

Похожие инструкции для E15CI100A

Бренды по названию

Популярные бренды

Follett E15CI100A, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание E15CI100A

Отзывы:

Похожие инструкции для E15CI100A

Бренды по названию

Популярные бренды