Foley 3096 Скачать руководство пользователя | Manualshive

Страница: 2 / 39

background image

2

SAFETY INSTRUCTIONS

1. KEEP GUARDS IN PLACE

and in working order.

2. REMOVE ADJUSTING KEYS AND WRENCHES.

.

3. KEEP WORK AREA CLEAN.

4. DON'T USE IN DANGEROUS ENVIRONMENT.

Don't use power tools in damp or wet locations, or
expose them to rain. Keep work area well lighted.

5. KEEP ALL VISITORS AWAY.

All visitors should be

kept a safe distance from work area.

6. MAKE WORKSHOP CHILD-PROOF.

With padlocks

or master switches.

7. DON'T FORCE THE GRINDER.

It will do the

j ob better and safer if used as specified in this manual.

8. USE THE RIGHT TOOL.

Don't force the grinder

or an attachment to do a job for which it was not
designed.

9. WEAR PROPER APPAREL.

Wear no loose clothing,

      gloves, neckties, or  jewelry  which may get caught in
      moving parts. Nonslip foot  wear is recommended.
      Wear protective hair covering to contain long hair.

10. ALWAYS USE SAFETY GLASSES.

11. SECURE WORK.

Mount the cutting unit in place

before grinding as prescribed in the operators
manual.

12. DO NOT OVERREACH.

Keep proper footing and

balance at all times.

13. MAINTAIN GRINDER WITH CARE.

Follow instructions in Service Manual for
lubrication and preventive maintenance.

14. DISCONNECT POWER BEFORE SEVICING.

15. REDUCE RISK OF UNINTENTIONAL
STARTING.

Make sure switch is in OFF

position before plugging in the grinder.

16. USE RECOMMENDED ACCESSORIES.

       Consult the manual for recommended
       accessories. Using improper accessories may
       cause risk of personal injury.

17. CHECK DAMAGED PARTS.

A guard or other

       part that is damaged or will not perform its
       intended function, should be properly repaired or
       replaced.

18. NEVER LEAVE GRINDER RUNNING
UNATTENDED. TURN POWER OFF.

Do not

leave back lapper until it comes to a complete
stop.

19. KNOW YOUR EQUIPMENT.

Read this manual

carefully. Learn its application and limitations as
well as specified potential hazards.

20. KEEP ALL SAFETY DECALS CLEAN &
LEGIBLE.

If safety decals become damaged or

       illegible for any reason, replace immediately.
       Refer to replacement parts illustrations in
       Service Manual for the proper location and part
       numbers of safety decals.

21. DO NOT OPERATE THE GRINDER
WHEN UNDER

the influence of drugs, alcohol,

or medication.

The

Warning Symbol

identifies special

instructions or procedures which, if not
correctly followed, could result in personal
injury, or loss of life.

The

Caution Symbol

identifies special

instructions or procedures which, if not strictly
observed, could result in damage to, or
destruction of equipment.

Safety Awareness Symbols

are inserted in this

manual to alert you to possible

Safety Hazards

.

Whenever you see these symbols, follow their
Instructions

«
1
2
3
4
...
»

Содержание 3096








































Отзывы:

Нет отзывов

Похожие инструкции для 3096

Бренд: Scarlett Страницы: 20

Бренд: Worx Страницы: 158

Бренд: Catler Страницы: 16

Бренд: Orphan espresso Страницы: 3

Бренд: Bunn Страницы: 2

Бренд: Lumme Страницы: 40

Бренд: Hitachi Koki Страницы: 80

Бренд: Dustless Страницы: 2

Бренд: Beta Страницы: 73

Бренд: Beta Страницы: 73

Бренд: Gude Страницы: 26

Бренд: U.S.SAWS Страницы: 10

Бренд: stayer Страницы: 80

Бренд: SOLIS Страницы: 64

Бренд: Sunex Tools Страницы: 13

Бренд: Gude Страницы: 160

Бренд: Parkside Страницы: 86

Бренд: Faust Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды