Focus Heterofocus 1400 Скачать руководство пользователя страница 19

 

 

 

 

Page 19 of 24

 

 
 
h) Damper operation and use: 
 
Use of supplied cold handle tool or protective glove is recommended to operate 
the  damper.  Do  not  touch  the  damper  handle  without  protection  when  a  fire  is 
operating. 
The heterofocus damper has four positions. The obturant  panel is in the  same 
direction  as  the  handle:  when  the  handle  is  vertical,  the  damper  is  fully  open. 
Handle  can  rotate  at  30°,  60°  and  90°  (horizontal :  closed).  In  closed  position 
the damper obturates by 75% the flue section. 
To modify the damper position, first pull the handle, then rotate and push again 
the handle in order to lock on a preset position. 

CAUTION : 

NEVER 

ADJUST 

THE 

DAMPER 

HANDLE 

ON 

AN 

INTERMEDIATE POSITION ! 

The damper position must be adapted to the fire intensity : during the lighting it 
must be fully open. Then it must be adjusted in order to reduce the smoke flow, 
so  the  heat  efficiency  will  be  optimal.  If  the  fireplace  spills  out  it  means  the 
damper is too obstructive : re-open the damper at the first signs of spillage. 
 
 
 
 
 

5 – MAINTENANCE: 

 
a) Taking out the ashes: 

CAUTION: BE SURE THE FIRE IS OUT AND THE FIREPLACE BODY COLD 
BEFORE REMOVING ASHES! 

To  remove  ashes  we  recommend  to  use  a  brush  and  a  shovel.  Dispose  of 
ashes  in  an  ash  container  (you  can  use  the  pedestal  tray  or  any  appropriate 
container). After cleaning, be sure to secure the fireplace properly! 

CAUTION :  DO  NOT  LIGHT  OR  FUEL  A  FIRE  USING  CARDBOARD  OR 
PLASTIC  OR  ANY  UNSTABLE  OR  VOLATILE  FUEL  SOURCE  OR  WITH 
FIRE  BRICKS  REMOVED,  AS  THIS  WILL  PRODUCE  OVER-FIRING  OR 
HOUSE  FIRE.  DAMAGE  CAUSED  FROM  NON-OBSERVANCE  OF  THIS 
CAUTION IS NOT COVERED UNDER FOCUS LIMITED WARRANTY.  
        
                 

Содержание Heterofocus 1400

























Отзывы: