Laser Sighting Device Installation Instruction
allen wrench
laser sighting device
laser diode
"L" bracket
laser diode
snap slot
4.Put the “L” bracket into slot of laser diode,
and use hexagon wrench to fix the rest screw
on each side.
3.Loosen the bolt and screw on both side of light by using
wrench and hex driver,rotate the light to the proper angle
and fasten the screws.
4.Wiring Diagram:
Input wire (three cores): black, white,
green Dimming wires: (two cores): purple, gray.
wrench
screw bolt
hex driver
A
purple DIM+
gray DIM-
black L white N green
A 4:1
1. Put the laser sighting device into the laser
diode.
3.Snap the side of the "L" bracket that is
without slot into the laser diode snap slot.
5.Insert the assembled laser sighting
equipment into the slot of the power
supply cover.
2. Choosing the hexagon wrench,to tight the
middle screw of the laser diode.
allen wrench
hexagon socket head
cap screws (SHCS)
the slot for power
supply cover
Warning
1. Before starting use of the light, please check if the light was damaged during transportation. If any damage shown,
pleases do not install or use it.
2. The products itself and all its components should not be mechanically stressed.
3. Installation must not damage or destroy conducting paths or other parts of the product.
4. Installation of LED product (with power supplies)needs to be made with regard to all applicable electrical and safety standards.
Only qualified personnel should be allowed to perform installations.
5. Correct electrical polarity needs to be observed. Wrong polarity may damage or destroy the LED products.
6. If fixing on metallic or otherwise conductive surfaces, there should be an electrical insulator between the product and the mounting surface.
7. All LEDs are static sensitive. Precautions should be taken to ensure that LEDs are well protected from ESD during handing,
even though the chips are safe in low static-electric discharge events.
8. DO NOT operate LEDs in reverse bias.
9. Damaged by corrosion will not be honored as a materials defect claim. It is the user's responsibility to provide suitable protection
against corrosive agents such as moisture and condensation and other harmful elements.
10. Identify Positive (+)and negative (-)outputs of the power supply by using a multimeter.
11. Electrical connection should be in a dry area unless adequately sealed.
12. This product series emits high light output. DO NOT look directly into the light emitting area. Direct exposure to the light over
an extended time period may harm eyes.
13. If the external flexible cable or cord of this luminaire is damaged, it shall be exclusively replaced by the manufacturer or his
service agent or a similar qualified person in order to avoid a hazard.
1. MIN 105°C SUPPLY CONDUCTORS / LES FILS D’ALIMENTATION 105°C MIN
2. SUITABLE FOR WET LOCATIONS / CONVIENT AUX EMPLACEMENTS MOUILLÉS
3. CAUTION - RISK OF FIRE. CAUTION - RISK OF SHOCK.
ATTENTION – RISQUE D’INCENDIE. ATTENTION – RISQUE DE CHOC.
4. THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON
FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.
CE PRODUIT DOIT ÊTRE INSTALLÉ SELON LE CODE D’INSTALLATION PERTINENT, PAR UNE PERSONNE
QUI CONNAÎT BIEN LE PRODUIT ET SON FONCTIONNEMENT AINSI QUE LES RISQUES INHÉRENTS.
This marking indicates that this product should not be disposed with other household wastes throughout the EU. To prevent possible
harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse
of material resources. To return your used device, please use the return and collection systems or contact the retailer where the
product was purchased. They can take this product for environmental safe recycling.
Correct Disposal of this product
6.Press the wireless laser button, the laser will be constant on.If it is a wired button,
then need to long presee until it is on. Laser will turn off when release the button.
7.After completed the installation of laser device,
then find and confirm the lighting spot on the
ground, and make a good mark.
8.Turn on the laser device, then adjust the angle of
stadium light, to make sure the laser can point at the
marked place on the ground. Secure the bolt
and screws by using the wrench and inner hexagon
screwdriver, to complete the final installation.
（
1
）
the wireless laser button
（
2
）
the wired laser button
Mark position
allen wrench
Bolt
Wrench
hexagon socket head
cap screws (SHCS)
the wireless
laser button
the wired
laser button
