background image

Important ESC and model information

The ESC included with the model has a safe start. If the motor battery is connected to the ESC and the throttle stick is not in 

the low throttle or off position, the motor will not start until the throttle stick is moved to the low throttle or off position. Once the 

throttle stick is moved to the low throttle or off position, the motor will emit a series of beeps. Several beeps with the same tune 

means the ESC has detected the cells of the battery. The count of the beeps equals the cells of the battery. The motor is now 

armed and will start when the throttle is moved.

The motor and ESC come pre-connected and the motor rotation should be correct. If for any reason the motor is rotating in the 

wrong direction, simply reverse two of the three motor wires to change the direction of rotation.

The motor has an optional brake setting. The ESC comes with brake switched off and we recommend that the model be flown 

with the brake off. However, the brake could be accidentally switched on if the motor battery is connected to the ESC while the 

throttle stick is set at full throttle. To switch the brake off, move the throttle stick to full throttle and plug in the motor battery. The 

motor will beep one time. Move the throttle stick to low throttle or the off position. The motor is ready to run and the brake will 

be switched off.

Battery election and Installation. We recommend the 11.1V 2200mAh 35C Li-Po battery. If using another battery, the battery 

must be at least a 11.1V 2200mAh 35C battery. Your battery should be approximately the same capacity, dimension and 

weight as the 11.1V 2200mAh 35C Li-Po battery to fit the fuselage without changing the center of gravity significantly.

   

1.

2.

3.

4.

10

EN

 Receiver wiring diagram  

The cables from the servo connector board should be 

connected to your receiver in the order shown. Note that the 

rudder channel controls both the steering servo and the rudder 

surface. The LEDs can be powered by any spare channel on 

the receiver. Tuck the wire leads into the recessed cavity 

towards the rear of the battery hatch. 

Get your model ready to fly

Spare

Содержание Kingfisher 1400mm















Отзывы: