FMI Vantage Hearth VUL24ND Скачать руководство пользователя

Страница: 11 / 36

www.fmiproducts.com

123220-01F

INSTALLATION

Continued

Heat Resistant
Material

(A)

Figure 5 - Heat Resistant Material (Slate,

Marble, Tile, etc.) Above Fireplace

Noncombustible

Material

Distance (A)

Requirements for Safe

Installation

12" or more

Noncombustible mate-
rial OK.

Between 8" and 12"

Install fireplace hood

accessory (GA6050 or
GA6053 see

Accesso-

ries

, page 34).

Less than 8"

Noncombustible mate-
rial must be extended
to at least 8". See

Between 8" and 12"

above. If you cannot ex-

tend material, you must
operate heater with flue

damper open.

MINIMUM NONCOMBUSTIBLE

MATERIAL CLEARANCES

If Not Using Mantel

Note: If using a mantel proceed to If Using
Mantel. If not using a mantel, follow the infor-
mation on this page.

You must have noncombustible material(s)

above the fireplace opening. Noncombustible
materials (such as slate, marble, tile, etc.)
must be at least 1/2" thick. With sheet metal,

you must have noncombustible material be-
hind it. Noncombustible material must extend
at least 8" up. If noncombustible material is

less than 12", you must install the fireplace

hood accessory. See Figure 5 for minimum
clearances.

If Using Mantel

You must have noncombustible material(s)

above the fireplace opening. Noncombustible
materials (such as slate, marble, tile, etc.)
must be at least 1/2" thick. With sheet metal,

you must have noncombustible material be-
hind it. Noncombustible material must extend
at least 8" up. If noncombustible material is

less than 12", you must install the fireplace

hood accessory. Even if noncombustible

material is more than 12", you may need the
hood accessory to deflect heat away from

your mantel shelf. See Figures 5 and 6 and

Figure 7, page 9, for minimum clearances.

IMPORTANT:

If you cannot meet these mini-

mum clearances, you must operate heater
with chimney flue damper open. Go to

Install-

ing Damper Clamp Accessory for Vented
Operation

, page 12.

MANTEL CLEARANCES

In addition to meeting noncombustible mate-

rial clearances, you must also meet required
clearances between fireplace opening and

mantel shelf. If you do not meet the clearances

listed below, you will need a hood.

Determining Minimum Mantel Clearance

If you meet minimum clearance between

mantel shelf and top of fireplace opening, a

hood is not required (see Figure 6).

Figure 6 - Minimum Mantel Clearances

Without Using Hood

Minimum
Noncombustible
Material

Minimum Non-
Combustible
Material Height

Distances to
Underside of
Mantel

Top of
Fireplace
Opening

Underside of
Mantel Shelf

12"

(A)

18" 20" 22" 24"

All minimum
distances are
in inches

Log Set

24"/30"

Models

1/2

10"

Mantel Shelf

Содержание Vantage Hearth VUL24ND





































Результаты поиска

Содержание Vantage Hearth VUL24ND

Отзывы:

Похожие инструкции для Vantage Hearth VUL24ND

Бренды по названию

Популярные бренды

FMI Vantage Hearth VUL24ND, Руководство владельца по эксплуатации и установке

Результаты поиска

Содержание Vantage Hearth VUL24ND

Отзывы:

Похожие инструкции для Vantage Hearth VUL24ND

Бренды по названию

Популярные бренды