FMI COMPACT HEAT MAJIC Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 30

background image

PROPANE/LP

VENT-FREE FIREPLACE SYSTEM

14

107107

For more information, visit www.desatech.com

INSTALLATION

Continued

CONNECTING FIREPLACE
TO GAS SUPPLY

Installation Items Needed

• Phillips screwdriver
• sealant (resistant to propane/LP gas, not

provided)

1.

Remove fireplace screen. Remove two
screws that hold fireplace screen in
place for shipping. These screws are
located near top of screen. Discard
screws. Lift fireplace screen up and pull
out to remove.

2.

Remove screws that attach branch sup-
port to fireplace (see Figure 25). Care-
fully lift up branch support and remove
from fireplace (see Figure 25).

3.

Route flexible gas line (provided by
installer) from equipment shutoff valve
into fireplace through side or rear ac-
cess holes in outer casing. Route flex-
ible gas supply line through fireplace
access holes in outer casing.

NOTICE: Most building codes do
not permit concealed gas con-
nections. A flexible gas line (see
Figure 26) is provided to allow
accessibility from the fireplace.
The flexible gas supply line con-
nection to the equipment shutoff
valve should be accessible.

4.

Apply pipe joint sealant lightly to male
threads of gas connector attached to
flexible gas line (see Figure 26). Con-
nect flexible gas line to flexible gas line
attached to gas valve of fireplace (see
Figure 26).

5.

Check all gas connections for leaks. See
Checking Gas Connections, page 15.

6.

Replace branch support back into fire-
place. Feed flexible gas line into fire-
place base area while replacing branch
support. Make sure the entire flexible
gas line is in fireplace base area. Reat-
tach branch support to fireplace with
screws removed in step 2.

Figure 25 - Removing Branch Support From Fireplace

Flexible Gas Line from
Fireplace Gas Valve
Provided with Fireplace

To Fireplace
Gas Valve

Figure 26 - Attaching Flexible Gas Lines Together

Gas Connector

Flexible Gas Line from
Equipment Shutoff
Valve Provided by
Installer

Equipment Shutoff
Valve

➞

To
External
Regulator

Branch
Support

Shoulder
Screw

Screen

➞

CAUTION: Avoid damage to

regulator. Hold gas regulator with
wrench when connecting it to gas
piping and/or fittings.

«
...
12
13
14
15
16
...
»

Содержание COMPACT HEAT MAJIC































Отзывы:

Нет отзывов

Похожие инструкции для COMPACT HEAT MAJIC

Бренд: Obadiah's Wood Stoves Страницы: 17

Бренд: Majestic Страницы: 2

Бренд: Majestic Страницы: 24

Бренд: Majestic Страницы: 63

Бренд: Majestic fireplaces Страницы: 36

Бренд: Majestic fireplaces Страницы: 16

Бренд: Majestic fireplaces Страницы: 28

Бренд: Majestic Страницы: 24

Бренд: Valcourt Страницы: 95

Бренд: UC Living Страницы: 28

Бренд: PRITY Страницы: 70

Бренд: Empire Comfort Systems Страницы: 4

Бренд: Astria Страницы: 24

Majestic Oak Series

Бренд: Majestic fireplaces Страницы: 2

Бренд: Hargrove Страницы: 7

Brentwood Gas Insert

Бренд: Pacific energy Страницы: 24

Бренд: HAMPTON BAY Страницы: 4

Бренд: Majestic Страницы: 48

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды