9
107105
OWNER’S MANUAL
INSTALLATION
Continued
36
5
/
8
"
25
7
/
8
"
51
3
/
4
"
26
7
/
8
"
Figure 10 - Rough Opening for Installing
in Corner
1.
Frame in rough opening. Use dimen-
sions shown in Figure 9 for the rough
opening.
If installing in a corner, use dimensions
shown in Figure 10 for the rough open-
ing. The height is 26
7
/
8
" which is the
same as the wall opening above.
2.
If installing GA3450(T) blower acces-
sory, do so at this time. Follow instruc-
tions included with blower accessory.
Note:
If not installing blower acces-
sory, you may wish to run electrical
wiring to your fireplace for future
blower installation (see Accessories,
page 26) Use only approved three-wire
electrical wiring.
BUILT-IN FIREPLACE
INSTALLATION
Built-in installation of this fireplace involves
installing fireplace into a framed-in enclo-
sure. This makes the front of fireplace flush
with wall. An optional brass trim kit acces-
sory is available (see Accessories, page 26).
Brass trim will extend past sides of fireplace
approximately 1/2 inch. This will cover the
rough edges of the wall opening. If install-
ing a built-in mantel above the fireplace you
must follow the clearances shown in Figure
12, page 10. Follow the instructions below
to install the fireplace in this manner.
Actual
Framing
Height
26"
26
7
/
8
"
Front Width
26
3
/
4
"
26
7
/
8
"
Depth
9
1
/
2
"
10
1
/
2
"
Bottom
3/4"
3/4"
WARNING: Do not allow any
combustible materials to overlap
the firebox front facing.
IMPORTANT:
Noncombustible materials
such as brick, tile, etc. may overlap the front
facing, but should never cover any neces-
sary openings like louvered slots.
Continued
26
7
/
8
"
26
7
/
8
"
3/4" Off
The Floor
Minimum
10
1
/
2
"
Figure 9 - Rough Opening for Installing in
Wall
WARNING: If pre-wiring, do
not connect wiring to any electri-
cal source at this time.
Install fireplace electrical outlet
and connect wiring to outlet be-
fore connecting to electrical
source. The fireplace electrical
outlet is included with the
GA3450(T) blower accessory.
Only use the fireplace electrical
outlet supplied with the
GA3450(T) blower accessory.
For convenience and efficiency, install
fireplace
• where there is easy access for operation,
inspection, and service.
• in coldest part of room.
An optional blower kit is available from
your dealer. See Accessories, page 26. If
planning to use blower, locate fireplace near
an electrical outlet.
Note:
A qualified installer should make
all electrical connections.
3.
Install gas piping to fireplace location.
This installation includes an approved
flexible gas line (if allowed by local
codes) after the equipment shutoff
valve. The flexible gas line must be the
last item installed on the gas piping.
4.
If you have not assembled firebox, fol-
low instructions on page 4.
5.
Carefully set fireplace in front of rough
opening with back of fireplace inside
wall opening.
6.
Attach flexible gas line to fireplace gas
regulator. See Connecting Fireplace to
Gas Supply, page 15.
7.
Bend four nailing flanges on outer cas-
ing with pliers (see Figure 11).
8.
Attach fireplace to wall studs using
nails or wood screws through holes in
nailing flange.
WARNING: Do not allow non-
combustible materials to cover
any necessary openings like lou-
vered slots.
WARNING: Use only noncom-
bustible mortar or adhesives when
overlapping the front facing with
noncombustible facing material.
WARNING: Never modify or
cover the louvered slots on the
front of the firebox.
9.
Check all gas connections for leaks. See
Checking Gas Connections, page 16.
10. If using optional brass trim kit, install
the trim after final finishing and/or
painting of wall. See instructions in-
cluded with brass trim accessory for at-
taching brass trim.
IMPORTANT:
When finishing your fire-
box, combustible materials such as wall board,
gypsum board, sheet rock, drywall, plywood,
etc. may be butted up next to the sides and top
of the firebox. Combustible materials should
never overlap the firebox front facing.
Figure 11 - Attaching Fireplace to Wall Studs
Nails or
Wood
Screws
Nailing
Flanges
