background image

www.fmiproducts.com

123755-01B

3

Figure 6 - Installing Mantel Top

Figure 7 - Installing Gas Fireplace

FIREPLACE INSTALLATION

1.  Fireplace  should  be  fully  assembled.  See 

Assembling 

Fireplace

 in fireplace owner’s manual.

2.  Mantel must be installed flush with two walls. Remove 

baseboard along walls where mantel is to be installed. 

Baseboard will prevent proper installation of mantel   and 

base.

3.  Place mantel base close to installation location. See fire-

place owner’s manual for installation clearances. Leave 

enough room to insert fireplace from back of mantel.

4.  If installing gas fireplace, install gas line. See 

Connecting 

to Gas Supply

 in fireplace owner’s manual. Remember to 

leave access to gas shutoff valve somewhere on mantel 

base or where it is accessible to user. Check for leaks. 

See 

Checking Gas Connections

  in  fireplace  owner’s 

manual.

5.  Position  fireplace inside  mantel through back opening 

(see Figure 7). Carefully position gas lines if applicable. 

IMPORTANT:

 Use caution when positioning fireplace on 

base. Base may scratch easily. Make sure fireplace is in 

proper position within mantel opening before continuing 

with installation.

6. 

Gas fireplace with louver door:

 Lower bottom louver 

door. Use two screws provided in fireplace hardware kit 

and attach fireplace to wooden base. Close louver door.

 

Gas fireplace with fixed louver:

 Before installing logs 

or burner assembly (see owner’s manual) remove screws 

securing floor to assembly. Lift floor for access to bot-

tom of fireplace. Use two screws provided in fireplace 

hardware kit and attach fireplace base to wooden base. 

Reinstall floor with screws removed previously.

IMPORTANT:

 Align mantel top left to right before installing. 

Back corner of mantel leg must be flush with edge of mantel 

top before installation.

IMPORTANT:

 If installing a gas fireplace, vertical support will 

be installed to mantel assembly after gas fireplace has been 

installed. If installing electric fireplace, first install vertical sup-

port and install fireplace from front of mantel. Do not put any 

weight on mantel top until vertical support has been installed.

Figure 5 - Installing Heat Reflector Strip

IMPORTANT: Make sure heat reflector strip is flush against 

header and spacers are on bottom side. Heat strip should 

NOT be flush with leg side but should have 1" clearance on 

both ends

 .

Header #4

Heat Reflector 

Strip

1¼'' Screws

Mantel Top 

Assembly

Assembly 

Blocks

Assembly 

Blocks

Corner 

of Mantel 

Legs Must 

be Flush 

with edge 

of Mantel 

Top

Mantel 

Legs Flush 

with Mantel 

Base

1¼'' 

Screws

Содержание C32GO

Страница 1: ...Base Support 11 Vertical Support Right Top Trim Strip Left Top Trim Strip Hardware Package 36 1 1 4 Wood Screws 114325 01 8 1 Finishing Nails 114295 04 4 2 Wood Screws 122447 01 Extra hardware may be included Tools required Power Screwdriver with 2 Phillips Bit Hammer Nail Set Ifanywoodpiecesaremissingordamaged contactthedealer whereyoupurchasedthismantelforreplacement Ifhardware is missing or dam...

Страница 2: ... Screws Base Support 10 Base 1 IMPORTANT Alignmantellefttorightonbasebeforeinstalling Corner of mantel legs must be flush with back of mantel base before installation see Figure 6 page 3 Use a tape measure to insure accuracy IMPORTANT Use2 screwsonlyontopcentersupport Using 2 screws in any other location will damage mantel Top Center Support 9 Mantel Top 5 Top Left Support 7 Top Triangle 6 Top Rig...

Страница 3: ...with louver door Lower bottom louver door Use two screws provided in fireplace hardware kit and attach fireplace to wooden base Close louver door Gas fireplace with fixed louver Before installing logs or burner assembly see owner s manual remove screws securing floor to assembly Lift floor for access to bot tom of fireplace Use two screws provided in fireplace hardware kit and attach fireplace bas...

Страница 4: ...d base into position in corner and flush against both walls Check operation of fireplace before proceeding 2 Place right trim strip on right side of top and left trim on left side of top Align both pieces so any gaps between mantel and wall are covered as well as possible and front of trim strips are flush with side of top With one person holding trim strips in place nail each strip to mantle usin...

Отзывы: