background image

GMr

接收机  Receiver

http://www.flysky-cn.com

Copyright ©2021 Flysky Technology co., ltd

发射机在更新完后,如无法与接收机对码,需强制更新接

收机。

1. 按住对码键同时给接收机上电,长按 10S, 接收机进入强

制更新状态,此时 LED 三闪一灭;

2. 在发射机端选择接收机更新并进入更新状态,更新过程

中 LED 三闪一灭;

3. 当发射机端显示 100% 即为更新成功,此时 LED 慢闪。

强制更新 

Forced update

失控保护

Failsafe

兼容性

Compatibility

该接收机兼容 PL18、NB4 和 NB4 Lite 等 AFHDS 3 协议发射机

注意事项:

•  使用前必须确保本产品与模型安装正确,否则可能导致模型发生严重损坏。

•  关闭时,请务必先关闭接收机电源,然后关闭发射机。如果关闭发射机电源时接收机仍然在工作,将有可能导致遥控设备失控或    

者引擎继续工作而引发事故。

•  确保接收机安装在远离电机,电子调速器或电子噪声过多的区域。

•  接收机天线需远离导电材料,例如金属棒和碳物质。为了避免影响正常工作,请确保接收机天线和导电材料之间至少有 1 厘米以

上的距离。

•  准备过程中,请勿连接接收机电源,避免造成不必要的损失。

Attention:

•  Make sure the product is installed and calibrated correctly, failure to do so may result in serious injury.

•  Make sure the receiver's battery is disconnected before turning off the transmitter, failure to do so may lead to unintended 

operation or loss of control.

•  Make sure the receiver is mounted away from motors, electronic speed controllers or any device that emits excessive 

electrical noise.

•  Keep the receiver's antenna at least 1cm away from conductive materials such as carbon or metal.

•  Do not power on the receiver during the setup process to prevent loss of control.

If after an update the transmitter is unable to connect or bind to the receiver, it is 

necessary to put the receiver into forced update mode.

1.Press and hold the Bind button while powering on the receiver simultaneously, 

press and hold for 10 seconds to enter forced update mode, during this time the 

LED flashes three times and off one time;

2. Select the receiver to update on the transmitter side to enter the update 

mode;the LED flashes three times and off one time during the updating process;

3. updating is successful when the receiver status indicator flashes slowly.

The receiver is compatible with PL18/NB4 and NB4 Lite all of  

transmitters which with AFHDS 3 protocol .

失控保护功能用于在接收机失去信号不受控制后,接收

机按设置好的失控保护值进行通道输出以保护模型及人

员安全。

•  本款接收机共支持三种失控保护模式 :" 无输出 "、

" 保持 "、" 固定值 ";“无输出”模式指在进入失控

保护状态后 PWM、PPM、i-Bus out、 i-Bus 2 转换

器保持无输出信号通道值,S.BUS、i-Bus2、i-bus

转换器输出最后收到发射机的信号通道值,“保持”

模式指在进入失控保护状态后,保持输出最后收到

发射机的信号通道值;“固定值”模式指在进入失

控保护状态后,保持设置的信号通道值进行输出信

号。

The failsafe function is used to output the channel according to the out-of-

control protection value set by the user after the receiver loses its signal 

and is out of control to protect the model and personnel.

•  This receiver supports three failsafe modes: "Free", "Hold", and "Fixed 

value"; "Free" mode refers to PWM, PPM, i-Bus out, i-Bus 2  converter 

entering the failsafe state keep the channel value of no output signal. The 

S.BUS, i-Bus2, and i-bus converters output the last received signal channel 

value of the transmitter. "Hold" mode means that after entering the failsafe 

state, keep the output of the last transmitter signal;the "Fixed value" mode 

means that after entering the out-of-control protection state, the set signal 

channel value is maintained to output the signal.

Отзывы: