background image

FS-SR8C

接收机  Receiver

http://www.flysky-cn.com

Copyright ©2022 Flysky Technology co., ltd

失控保护

Failsafe

失控保护功能用于在接收机失去信号不受控制后,接收机按设置好的失控保护值进行通道输出以保护模型及人员安全。
本款接收机共支持两种失控保护模式 : [ 无输出 ] 和 [ 有输出 ] 
[ 无输出 ] PWM 通道接口为无输出状态 ; 
[ 有输出 ] 输出设置的固定值。

注:1. 对于 PPM/i-BUS/S.BUS 等总线信号类型不允许单个或其中几个通道为 [ 无输出 ] 模式,通道设置为 [ 无输出 ] 模式时,实际信

号是保持最后输出值;
2. 因 S.BUS 信号信息包含失控标志位,各通道失控保护设置被失控标志位传达给后续设备,若连接的设备支持失控标志位解析,则失

控后,输出各通道设置的失控保护值;
3. 对于无失控标志位的信号 PPM/i-BUS,支持设置失控时信号 [ 无输出 ] 模式。设置为 [ 无输出 ] 模式后,不管各通道失控保护如何设

置,失控后各通道均为 [ 无输出 ] 模式。

The failsafe function is used to output the channel value according to the out-of-control protection value set by the user after 

the receiver loses its signal and is out of control to protect the model and personnel.
It can also be set  failsafe for each channel respectively. This receiver supports two failsafe modes: 

ON

 and 

OFF

 

OFF

 It is no output  for the interface of PWM. 

ON

 Outputs the failsafe values set for each channel. 

Notes

:

 

1.  For bus signal types such as PPM/i-BUS/S.BUS, a single or several of these channels are not allowed to be in 

OFF

 mode. The 

actual signal is held at the last output value when the channel is set to 

OFF

 mode.

2.  Because the S.BUS signal information contains failsafe flag bits, the failsafe settings of each channel are communicated to 

subsequent devices by the failsafe flag bits. If the connected devices support the failsafe flag bit analysis, the failsafe values set 

for each channel are output after out of control.

3.  For the signal PPM/i-BUS without failsafe flag bits, it supports the setting of the signal to 

OFF

 mode in case of out of control. 

After setting to 

OFF

 mode, regardless of the setting of the failsafe of each channel, each channel will be in 

OFF

 mode after out of 

control. 

注意事项:

•  使用前必须确保本产品与模型安装正确,否则可能导致模型发生严重损坏。

•  关闭时,请务必先关闭接收机电源,然后关闭发射机。如果关闭发射机电源时接收机仍然在工作,将会导致遥控设备失控。失控保

护设置不合理可能引起事故。

•  确保接收机安装在远离电机,电子调速器或电子噪声过多的区域。

•  接收机天线需远离导电材料,例如金属棒和碳物质。为了避免影响正常工作,请确保接收机天线和导电材料之间至少有 1 厘米以

上的距离。

•  准备过程中,请勿连接接收机电源,避免造成不必要的损失。

Attentions:

•  Make sure the product is installed and calibrated correctly, failure to do so may result in serious injury.

•  Make sure the receiver's battery is disconnected before turning off the transmitter, failure to do so can result out of control.   

Unreasonable setting of the Failsafe may cause accidents.

•  Make sure the receiver is mounted away from motors, electronic speed controllers or any device that emits excessive electrical 

noise.

•  Keep the receiver's antenna at least 1cm away from conductive materials such as carbon or metal.

•  Do not power on the receiver during the setup process to prevent loss of control.

Отзывы: