FS-SR12
接收机 Receiver
Http://www.flysky-cn.com
Copyright ©2022 Flysky Technology co., ltd
对码
Binding
本接收机固件更新需通过富斯遥控管家（FlySkyAssistant）完成（仅 3.0 及以上版本支持，富斯遥控管家固件可从官网 www.flyskytech.com 获取）。
本接收机可以通过以下两种方式进入更新：
1. 先将发射机与接收机对码后（接收机 LED 灯常亮），再将发射机与电脑连接，然后在电脑端打开富斯遥控管家，通过富斯遥控管家进行固件更新；
2. 将发射机与电脑连接，参考如下方式使接收机进入强制更新状态（接收机 LED 灯状态三闪一灭），然后在电脑端打开富斯遥控管家，通过富
斯遥控管家进行固件更新。
进入强制更新状态的操作方式如下：
• 先将接收机 BIND 和 CH11 通道的信号端相连接，然后给接收机上电；
• 按下对码按键，上电十秒钟后接收机 LED 灯状态三闪一灭，松开对码按键；
• 先给接收机上电，长按对码键十秒后接收机 LED 灯状态三闪一灭，松开对码按键。
The firmware of this receiver can be updated through the FlyskyAssistant (Only version 3.0 or above is supported. The firmware of
FlyskyAssistant is available on the Flysky official website ).
This receiver can be updated via the following two ways:
1. After the binding between the transmitter and the receiver (the LED of the receiver is solid on), connect the transmitter to the computer,
then open the FlyskyAssistant on the computer to update the firmware.
2. Connect the transmitter to the computer. Then put the receiver to enter the forced update mode by referring to the following way
(The LED
of the receiver operates in three-flash-one-off manner repeatedly). Afterwards, open the FlyskyAssistant on the computer to update the
firmware.
• Connect the signal pin of the BIND interface to the signal pin of the CH11 interface first, then power on the receiver.
• Power on the receiver while pressing and holding the BIND button for more than ten seconds, until the LED of the receiver operates in
three-flash-one-off manner repeatedly, then release the BIND button.
• Power on the receiver first, then press and hold the BIND button for more than ten seconds, when the LED of the receiver operates in
three-flash-one-off manner repeatedly, then release the BIND button.
固件更新
Firmware update
失控保护
Failsafe
失控保护功能用于在接收机失去信号不受控制后，接收机按设置好的失控保护值进行通道输出以保护模型及人员安全。
本款接收机共支持两种失控保护模式 : [ 无输出 ] 和 [ 有输出 ]
[ 无输出 ] i-BUS/PPM/PWM 通道接口为无输出状态 ;
[ 有输出 ] i-BUS/PPM/PWM 通道接口输出设置的固定值。
注：
1. 因为 S.BUS 信号包含失控标志位，所以接收机可通过失控标志位将“失控状态”信息传递到后续设备，而无需通过 [ 无输出 ] 状态传递（后续
The receiver supports two -way binding and one-way binding. The transmitter will display the information returned from the receiver after
the two-way binding is completed.
Follow the steps below to bind in two-way binding:
1. At the transmitter side, set
2WAY
for RF standard of the transmitter, then put the transmitter into bind mode.
2. The receiver supports three ways to enter bind mode: BIND button binding, bind cable binding and BIND button binding after power-on.
• BIND button binding: Press and hold the BIND button of the receiver while powering on the receiver, tthe LED of the receiver should be
flashing, indicating that the receiver is in bind mode. Then release the BIND button.
• Bind cable binding: Insert the bind cable to the BIND interface of the receiver, then power on the receiver. The LED of the receiver
should be flashing, indicating that the receiver is in bind mode. Note that you need to remove the bind cable from the receiver after the
binding process is completed.
• BIND button binding after power-on: The receiver has not been connected to the transmitter when it is powered on. Press and hold the
BIND button for 3 seconds, the LED of the receiver should be flashing, indicating that the receiver is in bind mode. Then release the
BIND button.
3. The receiver LED is always on after the binding is successful (The transmitter automatically exits the binding state after the successful
binding).
4. Check to make sure the transmitter and receiver functions are working correctly, repeat steps 1 to 3 (binding process) if any problems
arise.
Follow the steps below to bind in one-way binding:
1. At the transmitter side, set
1WAY
for RF standard of the transmitter, then put the transmitter into bind mode.
2. Put the receiver into bind mode (Refer to the description above for entering bind mode).
3. When the LED of the receiver is in slow flashing state, the binding process should be completed.
You need to manually put the transmitter
to exit the bind mode.
Then the LED of the receiver is solid on, indicating that the binding is completed.
4. Check to make sure the transmitter and receiver functions are working correctly, repeat steps 1 to 3 (binding process) if any problems
arise.
