FS-R4A
接收机 Receiver
http://www.flysky-cn.com
Copyright ©2021 Flysky Technology co., ltd
2. 正常开机，识别油门中点 :
•
上面第一步相关设备连接好后，先打开遥控器，并将遥控器油门扳机置于中点位置（自然状态）。 最后一步打开电调开关，接收机重新上电自动识别电池类型
后方可运行。
注意：
a. 电调开机后必须等到自检完成后方可运行（大约 3 秒），否则可能无法正常动作 ;
b. 若开机后无动力输出，请查看遥控器油门微调是否置于“0”位置，接收机重启可自动识别微调油门中点 ;
c. 若运行时发现电机转向不对，将电调接电机的两根线互换位置即可 ;
d. 为了一切正常，请养成先打开遥控器最后打开电调开关以及先关闭电调开关最后关闭遥控器的习惯。
注：
关于电调的电池类型、拖刹力度和运行模式的设置详见相关配套发射机说明书相关章节。
1.Connect related equipment：
•
Make sure the ESC is off before connection. Connect the motor with M+ and M- of ESC. Connect the steering servo to the 3Pin interface marked with “ST”
of ESC (- + S connected correspondingly). Connectthe battery with the positive and negative poles of ESC correspondingly.
2.Normal boot, identification throttle midpoint:
•
After connecting related equipment as step 1, turn on the radio first, move the throttle trigger to the neutral position . Turn on the switch of ESC at last.
The receiver will automatically recognize the battery type when it is powered on again.then can run it.
Note:
a.The ESC can be run after completing self-inspection (about 3 seconds) if power on, otherwise it cannot be operated normally.
b.If there is no power output and the red light of ESC flashes quickly after power on,Please check whether the throttle trim of the transmitter is set to the "0"
position, the receiver will automatically recognize the midpoint of the trim throttle after restarting;
c.If the rotation direction is not correct during running, exchange the two wires connecting motor and ESC.
d.To make sure everything is ok, please turn on the radio first and finally turn on the ESC, turn off the ESC first and finally turn off the radio.
Note: Please refer to the relevant sections for details about the battery type, drag brake force and running mode of the ESC.
电调功能使用说明
电调功能使用说明
ESC function instructions
电池
电机
电调 & 接收机
LED
舵机
Battery
Motor
Servo
LED
ESC&Rx
注意事项：
•
使用前必须确保本产品与模型安装正确，否则可能导致模型发生严重损坏。
•
请查看各动力设备以及车架说明书，确保动力搭配合理，避免因错误的搭配导致动力系统损坏。
•
勿使系统的外部温度超过 90℃ /194 ℉，高温将会毁坏动力系统。
•
关闭时，请务必先关闭接收机电源，然后关闭发射机。如果关闭发射机电源时接收机仍然在工作，将有可能导致遥控设备失控或者引擎继续工作而引发事故。
•
使用完毕后，若长时间不玩车，切记断开电池与电调的连接。如电池未断开，即使电调开关处于关闭状态，电调也会一直消耗电能（只是非常小），长时间连接
电池最终会被过放，进而导致电池或电调出现故障。我们不对因此而造成的任何损害负责！
•
确保接收机安装在远离电机或电子噪声过多的区域。
•
接收机天线需远离导电材料，例如金属棒和碳物质。为了避免影响正常工作，请确保接收机天线和导电材料之间至少有 1 厘米以上的距离。
•
准备过程中，请勿连接接收机电源，避免造成不必要的损失。
Attention:
•
Make sure the product is installed and calibrated correctly, failure to do so may result in serious injury.
•
Please carefully check each power device and car frame instructions to ensure the power matching is reasonable before use. Avoid damaging power system due
to incorrect matching.
•
Do not let the external temperature of the system exceed 90℃ /194 ℉ , because high temperature will damage the power system.
•
Make sure the receiver's battery is disconnected before turning off the transmitter, failure to do so may lead to unintended operation or loss of control.
•
After use, remember to disconnect the battery and the ESC. If the battery isn’t disconnected, the ESC will consume electric energy all the time even if it is off. It will
discharge completely if connect the battery for a long time, thus resulting in the failure of the battery or the ESC. We are not responsible for any damage caused by
this!
•
Make sure the receiver is mounted away from motors or any device that emits excessive electrical noise.
•
Keep the receiver's antenna at least 1cm away from conductive materials such as carbon or metal.
•
Do not power on the receiver during the setup process to prevent loss of control.
此功能用于当接收机无法正常收到发射机的信号不受控制时，保
护模型和操作人员的安全。 该接收机默认为油门通道固定为失控
进入刹车状态，其他通道失控后接收机无信号输出，如若在发射
机上进行设置，则按照设置值输出。
失控保护
Failsafe
This function is used to protect the safety of the model and the operator when the receiver cannot
normally receive the signal from the transmitter and is out of control. The receiver defaults that the
throttle channel is fixed to be out of control and enters the brake state. other channels has no signal
output. If you set it on the transmitter, it will output according to the set value.
