Flymo Glider Compact 330 VC, Руководство оператора

Страница: 6 / 20

Mains plug replacement - Important
• If the plug supplied is cut off it should be
destroyed. There is an electric shock hazard if a
cut off plug is inserted into a 13 amp socket.
1. No earth required. Flymo products are double
insulated to EN60335 and under no
circumstances should an earth be connected to
any part of the product.
2. Ensure the mains voltage suits your product.
3. Important!The wires in the mains lead are
coloured in accordance with the following code:
BLUE - NEUTRAL ; BROWN - LIVE. The wire
which is coloured BLUE must be connected to
the Terminal which is marked with the letter 'N' or
coloured BLACK. The wire which is coloured
BROWN must be connected to the Terminal
which is marked with the letter 'L' or coloured
RED.
4. It is important that the outer sheath is clamped
correctly into the 3-pin plug.
5. If in doubt consult your local Service Repairer or
qualified electrician before the machine is used.
6. A 13 Amp fuse must be fitted to the Mains Plug.
7. The normal plug fuse and household fuse only
protect the electrical equipment and are not a
safeguard against electrocution.
Training
1. Read the instructions carefully. Be familiar with
the controls and the correct use of the machine.
2. Never allow children or people unfamiliar with
these instructions to use the machine. Local
regulations can restrict the age of the operator.
3. Never operate the machine while people,
especially children, or pets are nearby.
4. Keep in mind that the operator or user is
responsible for accidents or hazards occurring to
other people or their property.
Preparation
1. While operating the machine always wear
substantial footwear and long trousers. Do not
operate the machine when barefoot or wearing
open sandals. Avoid wearing clothing that is
loose fitting or that hanging cords or ties.
2. Thoroughly inspect the area where the machine
is to be used and remove all objects which can
be thrown by the machine.
3. Before using, always visually inspect to see that
the blade, blade bolt and the blade assembly are
not worn or damaged. Replace worn or damaged
components in set to preserve balance. Replace
damaged or unreadable labels.
4. Before use check the supply and extension cord
for signs of damage or aging. If the cord
becomes damaged during use, disconnect the
cord from the supply immediately. DO NOT
TOUCH THE CORD BEFORE
DISCONNECTING THE SUPPLY. Do not use
the machine if the cord is damaged or worn.
Operation
1. Operate the machine only in daylight or in good
artificial light.
2. Avoid operating the machine in wet grass.
3. Always be sure of your footing on slopes.
4. Walk, never run.
5. Mow across the face of slopes, never up and
down.
6. Exercise extreme caution when changing
direction on slopes.
7. Do not mow excessively steep slopes.
8. Use extreme caution when reversing or pulling
the machine towards you.
9. Stop the blade(s) if the machine has to be tilted
for transportation when crossing surfaces other
than grass, and when transporting the machine
to and from area to be used.
10. Never operate the machine with defective guards
or shields, or without safety devices, for example
deflectors and/or grass collector, in place.
11. Switch on the motor carefully according to
instructions and with feet well away from the
blade(s).
12. Do not tilt the machine when switching on the
motor, except if the machine has to be tilted for
starting. In this case, do not tilt it more than
absolutely necessary and lift only the part, which
is away from the operator.
13. Do not start the machine when standing in front
of the discharge opening.
14. Do not put hands or feet near or under rotating
parts. Keep clear of the discharge opening at all
times.
15. Do not transport the machine while the power
source is running.
16. Stop the machine, and remove the plug from the
socket. Make sure that all moving parts have
come to a complete stop
• whenever you leave the machine,
• before clearing blockages or unclogging
chute,
• before checking, cleaning or working on the
machine,
• after striking a foreign object. Inspect the
machine for damage and make repairs before
restarting and operating the machine;
if the machine starts to vibrate abnormally (check
immediately)
• inspect for damage,
• replace or repair any damaged parts,
• check for and tighten any loose parts.
6 17 - 001 -