Flymo EasiMow 300R, Руководство оператора

Страница: 5 / 9

2. ASSEMBLY
DANGER! Risk of injury!
Cut injury when the product starts accidentally.
v
Disconnect the product from the mains and use gloves before
you assemble the product.
To assemble the handle:
Only for 300R [ Fig. A1 ]:
1. Put the lower handles on the shafts.
2. Put the washers on the shafts.
3. On the left side, screw the wingknob onto the shaft.
4. On the right side, screw the cable hook onto the shaft.
5. Screw the lower handles tight with the wingknob and the cable hook.
6. Put the upper handle on the lower handles and slide the screws
through the boreholes (there are 2 holes in the lower handle to choose
the desired height).
7. Put the washers on the screws.
8. On the left side, screw the wingknob onto the shaft.
9. On the right side, screw the cable hook onto the shaft.
10. Attach the control cable with the cable clips.
Only for 340R / 380R [ Fig. A2 / A3 ]:
1. Put the springs on the shafts.
2. Put the handle plates on the shafts.
3. Put the lower handle on the shafts.
4. Put the washers on the shafts.
5. On the left side, screw the wingknob onto the shaft.
6. On the right side, screw the cable hook onto the shaft.
7. Put the upper handle on the lower handle and slide the screws
through the boreholes.
8. Put the washers on the screws.
9. On the left side, screw the wingknob onto the shaft.
10. On the right side, screw the cable hook onto the shaft.
11. Attach the control cable with the cable clips.
g) When servicing the blades be aware that, even though the power source is
switched off, the blades can still be moved.
h) Use only genuine replacement parts and accessories.
Additional safety warnings
Electrical safety
DANGER! Cardiac arrest!
This product makes an electromagnetic field while it operates. This
field may under some conditions interfere with active or passive medical
implants. To decrease the risk of conditions that can possibly injure or
kill, we recommend persons with medical implants to speak with their
physician and the medical implant manufacturer before you operate the
product.
Do not use under wet conditions.
Do not operate in explosive atmospheres, such as in the presence of flammable
liquids, gases or dust.
Personal safety
DANGER! Risk of suffocation!
Small parts can be easily swallowed. There is also a risk that the polybag
can suffocate toddlers. Keep toddlers away when you assemble the
product.
Do not use the start levers alternately.
Do not disassemble the product further than the delivery status.
Use gloves, wear slip resistant shoes and wear eye protection.
Do not overload the mower.
Never operate the product when you are tired, ill or under the influence of alcohol,
drugs, or medicine.
Danger of slipping:
– in wet grass
– on steep slopes
– during transport
Be careful while going backwards.
To assemble the grass box [ Fig. A4 / A5 / A6 / A7 / A8 ]:
1. Push the grass box handle into the slots in the grass box cover until
it audibly engages.
2. Slide the grass box tongue into the slots in the grass box until it
audibly engages.
3. Align the grass box cover and the grass box locators.
4. Fold the grass box cover towards the grass box.
5. Push the grass box cover on the grass box. Make sure that all clips
are snapped in correctly.
To attach the grass box to the lawnmower [ Fig. A9 ]:
1. Lift the protective cover.
2. Attach the grass box to the hooks on the rear of the mower.
3. OPERATION
DANGER! Risk of injury!
Cut injury when the product starts accidentally.
v
Wait for the blade to stop, disconnect the product from
the mains and use gloves before you adjust or transport
the product.
To connect the mower [ Fig. O1 ]:
DANGER! Electric shock!
To avoid damage to the mains cable, the mains cable
must be inserted into the cable lock.
v
Before you operate insert the mains cable into the cable lock.
1. Loop the mains cable, insert the loop into the cable lock
9
and
pull tight.
2. Connect the mains cable to the mains.
To adjust the cutting height:
For the first cut of the season, always cut on the highest cutting height
possible, and gradually lower the cutting height over successive cuts to
your desired height for the lawn.
Only for 300R (in 3 positions) [ Fig. O2 / O3 / O4 / O5 / O6 ]:
The cutting height can be adjusted from 20 – 60 mm.
Position ‘Low’ (20 mm): Cutting height setting should only be used on
well maintained ‘manicured lawns’ without excessive moss or thatch.
Position ‘Mid’ (40 mm): Cutting height setting is the suitable for most
lawns.
Position ‘High’ (60 mm): Cutting height setting is used when you lawn
has excessive growth such as following holidays or first cut of the season.
v
Move both axles to the desired position in the E-Gate. Make sure that
both sides of the axle are in the same position. Make sure that both
axles are in the same position.
Only for 340R / 380R (in 5 positions) [ Fig. O7 ]:
The cutting height can be adjusted from 20 – 60 mm (from rear to front).
Position 1 (20 mm): Cutting height setting should only be used on well
maintained ‘manicured lawns’ without excessive moss or thatch.
Position 2 (30 mm): Cutting height setting is the suitable for most lawns.
Position 3 (40 mm): Cutting height setting is the suitable for most lawns.
Position 4 (50 mm): Cutting height setting is the suitable for most lawns.
Position 5 (60 mm): Cutting height setting is used when you lawn has
excessive growth such as following holidays or first cut of the season.
1. Pull the lever to the wheel.
2. Move the lever to the desired position.
3. Release the lever and let it engage.
To start the mower [ Fig. O8 ]:
DANGER! Risk of injury!
Risk of injury if the product does not stop when you
release the start lever.
v
Do not bypass the safety devices or switches. For example
do not attach the start lever to the handle.
5