unit
: mm ( ” )
4
FP40217-000
Dimensions
6
This document is printed with soy ink
(an organic ink made from soy oil) on
recycled paper. Environmentally
friendly printed matter.
FLYING MOLE CORPORATION
Waji-cho 5199-1, Hamamatsu-shi, 431-1115 Japan
Tel : +81-53-486-6030 Fax : +81-53-486-6033
http://www.flyingmole.co.jp, [email protected]
Never use liquids such as benzene, thinners, etc.,
chemically treated cloths, and do not spray any
aerosol type insecticides on the amplifier. Clean
the case using only a soft, dry cloth.
If the amplifier becomes soiled, mix a solution of
water and a neutral detergent then dampen a
soft cloth in the solution, wring out as much of
the solution as possible, and clean the amplifier.
Then use a soft, dry cloth to wipe the surface
dry.
Maintenance
5
7
Specifications
Connections
■
Installing the Unit
Align the rails on the top and bottom of the amp module with the grooves on the DPA-M1600
chassis and slowly slide the module fully into the chassis. Firmly fasten the screws on the
upper and lower right sides of the module’s front to fasten the module in place.
●
Make sure the Power Switch of DPA-M1600 is turned OFF, when wiring and checking polarities.
●
When connecting the speaker cables, make sure that the cables are securely separated between positive
and negative wires.
●
Connect the DPA-M1600’s power cable after all other connections are complete.
●
Jack names may differ according to the equipment being used. Please refer to the Owner’s Manual that
came with the device in question.
*1
The XLR (balanced) input wiring on the BI type is;
1
: GND,
2
: HOT,
3
: COLD.
Recommended Connector:
NEUTRIK NC3MX or similar.
*2 Recommended Connector:
NEUTRIK NL4FX or similar.
●
HT type
46.5
(1-13/16")
45
(1-3/4")
440 (17-5/16")
22.8
(7/8")
8.4
(5/16")
471.2 (18-9/16")
107.5 (4-1/4")
113.8 (4-1/2")
132.5
(5-3/16")
●
BI type
45
(1-3/4")
46.5
(1-13/16")
440 (17-5/16")
5.7
(1/4")
8.4
(5/16")
454.1 (17-7/8")
113.8 (4-1/2")
132.5
(5-3/16")
107.5 (4-1/4")
RCA Cable
RCA Cable
+
–
+
–
Preamp, etc.
Speaker
Speaker
DPA-M1600
(Pre Out)
(Pre Out)
AC Power is supplied via DPA-M1600
●
HT type
Preamp, etc.
Speaker
XLR Cable
(Pre Out)
(Pre Out)
XLR Cable
1+
+
1–
2+
2–
–
Speaker
+
–
DPA-M1600
(*1)
SPEAKON Connector
(*2)
AC Power is supplied via DPA-M1600
●
BI type
Neutral
detergent
Soft cloth
Liquids
Benzene
Rated Output
Frequency Response
Total Harmonic Distortion
S/N Ratio
Residual Noise
Input Sensitivity
Input Impedance
Input
SP Output
AC Power Connection
Volume Control Range
Power Consumption
Power Supply
Operating Conditions
Max. Dimensions
(main unit) inch / mm
Weight
* Specifications and/or product design are subject to change without notice due to product improvement.
HT Type
BI Type
100W (8
Ω
) x2 160W (4
Ω
) x2
5Hz~50kHz (8
Ω
/ +0,–3dB)
0.03% (8
Ω
/ 1kHz 50W output)
120dB (400Hz–30kHz BPF)
25
µ
V (400Hz–30kHz BPF)
1Vrms
2Vrms
10k
Ω
(maximum level)
47k
Ω
RCA (Unbalanced)
XLR (Balanced)
Binding Post
SPEAKON
Supplied via DPA-M1600 (AC Outlet)
0 ~ –30dB
2ch : 45W / 8
Ω
, 65W / 4
Ω
AC 120V 60Hz (U.S.A. & Canadian model) / AC 230V 50Hz (European model)
Other areas : Mentioned on side of module.
0
°
C ~ 40
°
C
1-13/16”(W) x 5-3/16”(H) x 18-9/16”(D)
1-13/16”(W) x 5-3/16”(H) x 17-7/8”(D)
46.5(W) x 132.5(H) x 471.2(D) mm
46.5(W) x 132.5(H) x 454.1(D) mm
1.4kg (3.08lbs)
Limited Warranty
8
Warranty period is shown by distributor in your market.
In case defects occur during this period not due to mishandling modification or shipping damage
due to improper packing is used for transportation.
Please send the product together with proof of purchase to the dealer where you had purchased
or to the following address if it is shown.