Fluke ScopeMeter 190 Series III Скачать руководство пользователя страница 53

Страница: 53 / 70

ScopeMeter® Test Tool

Calibration Adjustment

4. Set the 5502A to operate (OPR).

5. Press

to start the calibration.

Wait until the display shows the calibration status

:READY

6. Press

to select the next calibration step, set the 5502A to the next calibration

point, and start the calibration.

7. Continue through all calibration points for

Multimeter Ohm Gain

until the display shows the

status

CL 0916: READY

When you are finished, set the 5502A to Standby.
Continue at the

Save Calibration Data and Exit

section.

Save Calibration Data and Exit

To save the calibration data and exit the Maintenance mode:
1. Remove all test leads from the Test Tool inputs.

2. Press

(SAVE). The Test Tool shows on the display:

Calibration data valid.
Save data and exit maintenance mode?

Note

Calibration data valid indicates that the calibration adjustment procedure is performed

correctly. It does not necessarily mean that the Test Tool meets the specifications.

3. Press

(YES) to save and exit.

Note

After saving the calibration data, the calibration number and date updates if the

calibration data changes and the data are valid. The calibration number and date do not

change if:



the calibration mode is entered and left without doing a calibration adjustment



only the probe calibration was done



you press

(NO), the Test Tool returns to the calibration mode



you can either calibrate the Test Tool again, or press

(EXIT), (YES) to save and

exit

Error messages:

WARNING: Calibration data not valid.
Save data and exit maintenance mode?

Содержание ScopeMeter 190 Series III







































































Результаты поиска

Содержание ScopeMeter 190 Series III

Отзывы:

Похожие инструкции для ScopeMeter 190 Series III

Бренды по названию

Популярные бренды

Fluke ScopeMeter 190 Series III, Руководство по обслуживанию

Результаты поиска

Содержание ScopeMeter 190 Series III

Отзывы:

Похожие инструкции для ScopeMeter 190 Series III

Бренды по названию

Популярные бренды