Fluke ScopeMeter 190 Series III Скачать руководство пользователя страница 14

Страница: 14 / 70

190 Series III

Service Manual

Input A, B, C, D DC Voltage Accuracy Test

Warning

To prevent possible electrical shock, fire, or personal injury, ensure that the

calibrator is in standby mode before making any connection between the

calibrator and the Test Tool. Dangerous voltages are present on the calibration

source and connection cables during these steps.

Note

The test steps for channel C and D are only for the 4-channel models.

To verify the automatic dc voltage scope measurement:
1. Connect the Test Tool to the 5502A as shown in see

Figure 3

Figure 3. Test Tool Inputs A, B, C, D to 5502A Normal Output

2. Select the Test Tool setup:

a. Recall the setup (see

Standard Test Tool Setup

). Press

(RECALL) and

select

SETUP

b. Press

, select the setup name, and press

to recall the setup.

c. Press

, press

(INPUT A OPTIONS...), and select

Attenuator: Normal |

Bandwidth: 10 kHz

for the available setting in the ScopeMeter.

d. Press

, press

(INPUT B OPTIONS...), and select

Attenuator: Normal |

Bandwidth: 10 kHz

for the available setting in the ScopeMeter.

e. Press

, press

(INPUT C OPTIONS...), and select

Attenuator: Normal |

Bandwidth: 10 kHz

for the available setting in the ScopeMeter.

f. Press

, press

(INPUT D OPTIONS...), and select

Attenuator: Normal |

Bandwidth: 10 kHz

for the available setting in the ScopeMeter.

g. Press

to clear the softkey menu and the full 8-divisions display.

NORMAL

SCOPE

FLUKE 5502A CALIBRATOR

PM9091

PM9081

CONNECT TO CHANNEL A, B, C, D IN PARALLEL

TERMINATION

PM9093

PM9092

METER

PM9092

2 CHAN. + METER

4 CHANNELS

Содержание ScopeMeter 190 Series III







































































Результаты поиска

Содержание ScopeMeter 190 Series III

Отзывы:

Похожие инструкции для ScopeMeter 190 Series III

Бренды по названию

Популярные бренды

Fluke ScopeMeter 190 Series III, Руководство по обслуживанию

Результаты поиска

Содержание ScopeMeter 190 Series III

Отзывы:

Похожие инструкции для ScopeMeter 190 Series III

Бренды по названию

Популярные бренды