manualshive.com logo in svg

Fluke PG9000 Series, Руководство по эксплуатации и обслуживанию

Поделиться
Скачать
Fluke PG9000 Series Скачать руководство пользователя страница 46

PG9602™ OPERATION AND MAINTENANCE MANUAL 

© 2011 Fluke Calibration 

Page 

36

 

3.4.1 

Piston Position Ready/Not Ready 

The piston position 

Ready/Not Ready 

character indicates 

Ready 

or 

Not Ready

 based on the float 

position of the piston (see Section 3.5) and an automated measure generation status (see Section 
3.10.9).  This ensures that pressure definitions will be made with the piston not more than a 
certain distance from mid-float position and that measurements will not be made while the action 
of an automated pressure controller is active which may influence the pressure.  The default 
ready range is -2.5 mm to +2.5 mm relative to the center float position of 0.0 mm. 

The piston position 

Ready/Not Ready 

character is the first character from the left on the top 

line of the main run screen. 

The piston position

  Ready/Not Ready

  criterion is determined by the current SETUP file and 

can be customized by the user (see Section 3.11). 

Piston position 

Ready/Not Ready

 character indications include: 

< * >

 

Piston position Ready 

(within the position limits specified in the current SETUP file) 

(see Section 3.5). 

<

↓

>

 

Piston position Not Ready, low

  (below the position limits specified in the current 

SETUP file, see Section 3.11).  The 

<

↓

>

 flashes if the piston is not at the bottom stop 

position to alert the user that this indicator is 

Not Ready

. 

<

↑

>

 

Piston position Not Ready, high

  (above the position limits specified in the current 

SETUP file) (see Section 3.11).  The 

<

↑

>

 flashes if the piston is not at the top stop 

position to alert the user that this indicator is 

Not Ready

. 

<?>

 

Piston position not known 

(current specified mass load is less than the load of the piston 

+ bell). The mass carrying bell must be installed for PG9000 piston position measurement 
to operate correctly – any random piston position values that may be indicated are not valid 
when the mass carrying bell is not installed. 

Note 

Piston position always indicates Not Ready  if automated pressure 
generation is adjusting pressure, regardless of actual piston position. 

3.4.2 

Piston Rotation Rate Ready/Not Ready 

The piston rotation 

Ready/Not Ready 

character indicates 

Ready 

or 

Not Ready

 based on the 

rotation rate of the piston. 

The piston rotation 

Ready/Not Ready 

character is the second character from the left on the 

top line of the main run screen. 

The piston rotation rate 

Ready/Not Ready 

criterion is specific to the currently active piston 

cylinder module and can be edited by the user (see Sections 3.12.1.1). 

Piston rotation rate 

Ready/Not Ready

 character indications include: 

< * > 

Rotation rate Ready: 

Rotation rate is within the rotation rate limits specified in the 

current piston-cylinder module file) (see Section 3.12.1.1). 

<

<

>

 

Rotation rate Not Ready, low:

 Rotation rate is less than the lower rotation rate limit 

specified in the current piston-cylinder module file (see Section 3.12.1.1) 
or motorized rotation system is currently engaged.  Note that the low rotation limit is 
automatically reduced when the mass loaded on the piston is less than 3 kg.  The 

<

<

>

 flashes if the piston is floating to alert the user that this indicator is 

Not Ready

. 

<?>

 

Rotation rate not known: 

Current specified mass load is less than the load of the 

( bell).  The bell must be installed for PG9000 piston rotation rate measurement 
to operate correctly so piston rotation rate cannot be measured when the bell is not 
installed. 

Note 

At mass loads less than 3 kg the low rotation limit is automatically reduced 
to an operational minimum to maximize free rotation time. 

Содержание PG9000 Series











































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды