manualshive.com logo in svg

Fluke PG9000 Series, Руководство по эксплуатации и обслуживанию

Поделиться
Скачать
Fluke PG9000 Series Скачать руководство пользователя страница 110

PG9602™ OPERATION AND MAINTENANCE MANUAL 

© 2011 Fluke Calibration 

Page 

100

 

2.  The second head function is the head correction for the PG9000  reading of atmospheric 

pressure that is used to calculate air density, and/or to add to atmospheric pressure in absolute 
by adding atmosphere mode. The barometer reading atmospheric pressure may not be at the 
same height as the piston reference level and, if so, a head correction is needed to determine 
atmospheric pressure at the piston reference level. This head correction is referred to as ATM 
head. The ATM head height can be edited by pressing 

[SPECIAL]

  and selecting 

<3head>

, 

<3atm>

.  The ATM head is only applied to internal or external barometer readings. It is not 

applied to normal or user values of atmospheric pressure. 

3.  The third head function  is the automated correction for the piston position, referred to as 

PISTON head.  The PG9602 reference level marked on the mounting post is the level at 
which pressures are defined when the piston is in midstroke position –  0.0 mm.  As the 
piston moves away from midstroke, the pressure definition reference level 
moves proportionally.  PG9000’s automated correction for piston position calculates the 
head pressure corresponding to the change  in piston position from midstroke and 
compensates the defined pressure.  In this way, the defined pressure calculated by 
PG9000 is always the pressure at the reference level marked on the mounting post, even 
if the piston is not at midstroke position.  The PISTON head function can be turned ON 
and OFF by pressing 

[SPECIAL]

 and selecting 

<3head>

, 

<4piston>

. 

Note 

See Section 7.2.2  for information on calculation of the three 
fluid head correction functions. 

  OPERATION 

To access various fluid HEAD correction functions press 

[SPECIAL]

, and select 

<3head>

. The display is: 

Edit head: 1fluid 

2unit 3atm 4piston 

 

•

 

<1fluid>

 to change the DUT head fluid (see Section 3.12.3.1). 

•

 

<2unit>

 to specify the DUT head height unit of measure (see Section 3.12.3.2). 

•

 

<3atm>

 to adjust the ATM head height (see Section 3.12.3.3). 

•

 

<4piston>

 to turn the PISTON head correction ON and OFF  (see Section 3.12.3.4). 

3.12.3.1  <3head>, <1fluid> 

 

OPERATION 

•

 

To specify the DUT head fluid (see 
Section  3.12.3, PRINCIPLE), press 

[SPECIAL]

  and select 

<3head>

, 

<1fluid>

.  The display is: 

Head fluid: 

1gas 2liquid 

 

•

 

If 

<1gas>

  is selected, the display 

offers the choice of three gasses.  
Making a gas selection returns to the 
previous run screen with that gas 
active for the DUT head function.  
The display is: 

Gas type: 

1N2 2He 3Air 

 

•

 

If 

<2liquid>

  is selected, the display 

offers the choice of oil, water or a 
user defined liquid.  If the user 
defined liquid is selected, its density 
must be specified.  Making a liquid 
selection returns to the previous run 
screen with that liquid active for the 
DUT head function. The display is: 

Liquid type: 

1oil 2H20 3user 

 

Содержание PG9000 Series











































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды