FlashPort
Cable
Warranty
The warranty for your Product is on the Fluke Networks website,
visit:
www.flukenetworks.com/warranty
Class A Equipment (Industrial Broadcasting & Communication
Equipment)
This product meets requirements for industrial (Class A)
electromagnetic wave equipment and the seller or user
should take notice of it. This equipment is intended for
use in business environments and is not to be used in
homes.
A
급 기기 ( 업무용 방송통신기자재 )
이 기기는 업무용 (A 급 ) 전자파적합기기로서 판매자 또는
사용자는 이 점을 주의하시기 바라며 , 가정외의 지역에서
사용하는 것을 목적으로합니다
.
FCC Statement
Note: This equipment has been tested and found to comply
with the limits for a Class A digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential
area is likely to cause harmful interference, in which case the
user will be required to correct the interference at his own
expense.
Properly shielded and grounded cables and connectors must
be used in order to meet FCC emission limits. Fluke Networks
is not responsible for any radio or television interference
caused by using other than recommended cables and con-
nectors or by unauthorized changes or modifications to this
equipment. Unauthorized changes or modifications could void
the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC rules. Operation
is subject to the following two conditions: (1) this device
may not cause harmful interference, and (2) this device must
accept any interference received, including interference that
may cause undesired operation.
Advertise:
10/100/1000 HDx/FDx
Rx Pair:
1,2
Polarity:
normal
192.168.001.001
47V
47V
2ms, 5ms,–
Name:
Core-Switch02.dhr.com
Port:
GigabitEthernet1/0/47
VLAN:
21
Model: cisco WS-C2960S-48TS-L
IP/MAC: 172.031.163.010
Server: 193.211.132.127
Subnet:
255.255.254.000
DNS1:
192.181.002.170
DNS2
: 192.181.002.173
Type:
TCP
Port:
80(HTTP)
IP:
172.016.200.100
84ms, 89ms, 73ms
10/
100
/1000 HDx/
FDx
Core-Switch02.dhr.com
192.168.001.100
www.google.com
Environmental & Regulatory
Specifications
Environmental
Operating Temperature and
Relative Humidity
32°F to 122°F (0°C to 50°C ), Relative
Humidity 5% to 90%, Non-con-
densing
Storage temperature
-4°F to 140°F (-20°C to 60°C)
Shock and vibration
Random 2g, 5Hz - 500 Hz (class 2),
1 m drop
Safety
IEC 61010-1, CAT none, Pollution
degree 2
Operating altitude
13,123 ft (4,000 m)
Storage altitude
39,370 ft (12,000 m)
EMC
IEC 61326-1, Portable
Wireless (Models 200/300 only)
Specification Compliance
IEEE 802.11 b/g
Frequency Channels
802.11 Channels 1 thru 11, default
is 11
Operating Frequency
2.412~2.484 Ghz, ISM Band
Regulatory Domain
EN 301 489-1/17
General
Dimensions
4.36”x 1.6” x 1.28” (11.07 cm x 4.06
cm x 3.25 cm)
Weight with batteries
Model 100: 0.250 lb (0.113 kg)
Model 200: 0.255 lb (0.116 kg)
Model 300: 0.255 lb (0.116 kg)
Battery
2 AA Alkaline, IEC LR6, or ANSI/
NEDA 15A
Browser
Internet Explorer 9.0, Firefox 3.6,
Chrome 5.0, Safari 5.1 (minimum
revision).
6
FCC Statement
Changes or modifications to the wireless radio not
expressly approved by Fluke Corporation will void the
user's authority to operate the equipment. This device
complies with Part 15 of the FCC Rules. Operation is sub-
ject to the two conditions that follow: (1) this device can
not cause interference, and (2) this device must accept
any interference, including interference that can cause
undesired operation of the device. Class B digital device:
A digital device that is marketed for operation in a resi-
dential environment notwithstanding use in commercial,
business and industrial environments. Examples of such
devices include, but are not limited to, personal comput-
ers, calculators, and equivalent electronic devices that are
marketed for operation by the general public. The Meter
was tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential
installation. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and
used in accordance with the instructions, can cause harm-
ful interference to radio communications. However,
there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harm-
ful interference to radio or television reception, which
can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference
by one or more of the measures that follow:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
Consult the dealer or an experienced radio/TV technician
for help. The term "IC:" before the radio certification
number only signifies the device meets Industry's Canada
technical specifications.
W
Warning
X
(continued)
• Remove the batteries if the Product is not used for an extended period of time,
or if stored in temperatures above 50 °C. If the batteries are not removed,
battery leakage can damage the Product.
• The battery door must be closed before you operate the Product
• Repair the Product before use if the battery leaks.
• Turn off the Product and disconnect all cables before you replace the batteries.
• Be sure that the battery polarity is correct to prevent battery leakage.
•
Do not put battery cells near heat or fire.
• Do not operate the Product with covers removed or the case open. Hazardous
voltage exposure is possible.
• Clean the case with only a damp cloth with water.
• Have an approved technician repair the Product.
• Do not short the battery terminals together.
Mobile Interface (Models 200/300 only)
Tools Menu
(model 300 only)
WWW
www.google.com:80(HTTP)
Wi-Fi
LinkSprinter, <Ch2>
IP
DHCP
Notification
Auto-off
Test 1Gb
Off
On
On
Test at 1Gb
when advertised,
set to off by
default
3 minute Auto-off
Send test results
to cloud
Configure DHCP
or static IP address
Configure target
DNS name or IP
address, Configure
PING or TCP port
test type
Configure SSID and
channel of built-
in AP
Power over Ethernet
voltage
Bold indicates
actual link speed
and duplex
Advertised Link
Speed and Duplex,
Receive Pair and
polarity
Name of nearest switch
DHCP address received
Gateway IP address
Target DNS name or
IP address
Ping or TCP port
IP address if DNS name
TCP or PING response
times (3)
Switch Port Advertise-
ment from LLDP or
CDP (optional)
DHCP server, subnet
and DNS server address
Ping response times (3)
-- means no response
Symbols
W
Warning or Caution: Risk of damage or destruction
to equipment or software. See explanations in the
manuals.
X
Warning: Risk of fire, electric shock, or personal
injury.
*
Warning: Class 1 or Class 2 lasers. Risk of eye damage
from hazardous radiation.
j
Do not connect the Product to a public telephone
system.
P
Conformite Europeene. Conforms to the requirements
of the European Union and the European Free
Trade Association (EFTA).
)
Listed by the Canadian Standards Association.
The Product complies with Australian standards.
)
IC
This device complies with Industry Canada license-exempt RSS
standard(s). Operation is subject to the following two condi-
tions: (1) this device may not cause interference, and (2) this
device must accept any interference, including interference that
may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada
applicables aux appareils radio exempts de licence. L’exploita-
tion est autorisée aux deux conditions suivantes : (1) l’appareil
ne doit pas produire de brouillage, et (2) l’utilisateur de
l’appareil doit accepter tout brouillage radioélectrique subi,
même si le brouillage est susceptible d’en compromettre le
fonctionnement.
The radio transmitter has been approved by Industry Canada
to operate only with the antenna supplied. Use of any other
antenna is strictly prohibited for use with this product.
L’émetteur radio a été approuvé par Industrie Canada pour
fonctionner uniquement avec l’antenne fournie. L’utilisation
de toute autre antenne est strictement interdit d’utiliser ce
produit.
4
Table 1: Symbols
Safety......... Meets IEC 61010-1: CAT none, pollution degree 2
EMC ........... Meets IEC62136-1: Portable
This KCC statement applies to the following Products:
OptiView XG Performance Test Remote, LinkRunner AT Network
AutoTester, LinkRunner Network Multimeter, and NetTool Series II.
W
Warning or Caution: Risk of damage or destruction
to equipment or software. See explanations in the
manuals.
X
Warning: Risk of fire, electric shock, or personal
injury.
*
Warning: Class 1 or Class 2 lasers. Risk of eye damage
from hazardous radiation.
j
Do not connect the Product to a public telephone
system.
P
Conformite Europeene. Conforms to the require-
ments of the European Union and the European Free
Trade Association (EFTA).
)
Listed by the Canadian Standards Association.
The Product complies with Australian standards.
Certifications and Compliance
P
Conformite Europeene. Conforms to the requirements of the
European Union and the European Free Trade
Association (EFTA).
Listed by the Canadian Standards Association.
Conforms to relevant Australian standards
IC
The term “IC” before the radio certification number only signi-
fies the device meets Industry’s Canada technical specifications.
Conforms to the relevant EMC and safety standards of South
Korea.
4
Table 1: Symbols
Safety......... Meets IEC 61010-1: CAT none, pollution degree 2
EMC ........... Meets IEC62136-1: Portable
This KCC statement applies to the following Products:
OptiView XG Performance Test Remote, LinkRunner AT Network
AutoTester, LinkRunner Network Multimeter, and NetTool Series II.
W
Warning or Caution: Risk of damage or destruction
to equipment or software. See explanations in the
manuals.
X
Warning: Risk of fire, electric shock, or personal
injury.
*
Warning: Class 1 or Class 2 lasers. Risk of eye damage
from hazardous radiation.
j
Do not connect the Product to a public telephone
system.
P
Conformite Europeene. Conforms to the require-
ments of the European Union and the European Free
Trade Association (EFTA).
)
Listed by the Canadian Standards Association.
The Product complies with Australian standards.
Results Page
Settings Menu
W
Warning
X
To prevent possible fire, electric shock, or personal injury:
• Read all safety information before you use the Product.
• Carefully read all instructions.
• There are no user serviceable parts inside.
• Do not modify the Product.
• Do not touch voltages > 30 VAC rms, 42 VAC peak, or 60 VDC.
• Do not use the Product around explosive gas, vapor, or in damp or wet
environments.
• Examine the case before you use the Product. Look for cracks or missing
plastic.
• Use this Product indoors only.
• Do not connect the Product to voltages that are higher than the maximum
voltage rating for the Product.
• Do not connect the Product to a telephone line.
•
Use the Product only as specified, or the protection supplied by the Product
can be compromised.
• Do not use the Product if it is damaged.
• Do not use the Product if it operates incorrectly.
• Batteries contain hazardous chemicals that can cause burns or explode. If
exposure to chemicals occurs, clean with water and get medical aid.
Software Notice
This product uses:
FreeRTOS - Copyright (C) 2010 Real Time Engineers Ltd
FreeRTOS information can be found at www.freertos.org.
lwIP - Copyright (c) 2001-2004 Swedish Institute of Computer Science.
jQuery/jQuery mobile - Copyright 2013 The jQuery Foundation.
uIP - Copyright (c) 2004, Swedish Institute of Computer Science.
All rights reserved.
Software license statements and files are available at Linksprinter.io/licenses
lwIP is licenced under the BSD licence:
Copyright (c) 2001-2004 Swedish Institute of Computer Science.
All rights reserved.
Redistribution and use in source and binary forms, with or without modification,
are permitted provided that the following conditions are met:
1. Redistributions of source code must retain the above copyright notice,
this list of conditions and the following disclaimer.
2. Redistributions in binary form must reproduce the above copyright notice,
this list of conditions and the following disclaimer in the documentation
and/or other materials provided with the distribution.
3. The name of the author may not be used to endorse or promote products
derived from this software without specific prior written permission.
THIS SOFTWARE IS PROVIDED BY THE AUTHOR ``AS IS AND ANY EXPRESS OR
IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WAR-
RANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
DISCLAIMED. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT,
INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTH-
ERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF
ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
Copyright 2013 jQuery Foundation and other contributors http://jquery.com/
Permission is hereby granted, free of charge, to any person obtaining a copy of
this software and associated documentation files (the”Software”), to deal in the
Software without restriction, including without limitation the rights to use, copy,
modify, merge, publish,distribute, sublicense, and/or sell copies of the Software,
and topermit persons to whom the Software is furnished to do so, subject tothe
following conditions:The above copyright notice and this permission notice shall
beincluded in all copies or substantial portions of the Software.THE SOFTWARE
IS PROVIDED “AS IS”, WITHOUT WARRANTY OF ANY KIND, EXPRESSED OR
IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANT-
ABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN
NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BELIABLE FOR
ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTIONOF
CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTIO
WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.
Go to LinkSprinter.com to learn more about how to use your
LinkSprinter.
Open Cable
test results
Flash a switch port
to confirm wiring
Cable
< Back
1
2
3
6
4
5
7
8
Open <3.3ft
Good 10.5ft
Good 10.5ft
Good 10.5ft
