Fluke 1594A Скачать руководство пользователя страница 29

Страница: 29 / 36

Gettingstarted

Usersettingsscreen

5 Getting started

5.1 Powering on the Super-Thermometer

CAUTION:

Before powering the Super-Thermometer on, ensure that the line voltage selection is set

properly. Refer to Section 3.3, Line voltage and fuses, on page 11 for instructions.

Power the Super-Thermometer on by setting the power switch located on the back panel to the On position.

After power is on, pressing the Power Standby switch on the front panel puts the system into hibernation, leav-

ing key components such as the resistor oven powered on.
The first time the unit is powered on, the User Settings screen will be displayed after startup. Later in the sec-

tion it will be explained how this feature is turned off so the Measurement screen is displayed when the unit is

powered on.

5.2 User settings screen

The User Settings screen allows the user to configure system settings such as language, temperature measure-

ment resolution, screen saver settings and alarms. As mentioned previously, the User Settings screen is the first

displayed upon the first power-up. This feature can be turned off by the user after the user settings have been

configured.
The following fields are displayed in the User Settings screen:

LANGUAGE-

sets the language in which the menus and screens are displayed. The options are ENGLISH,

CHINESE, JAPANESE,SPANISH, GERMAN, FRENCH, and RUSSIAN. ENGLISH is the default option.

DATE FORMAT-

sets the format used to display dates on the screen. Available options are YYYY-MM-DD,

MM-DD-YYYY, and DD/MM/YYYY. The default option is YYYY-MM-DD. This setting has no effect on

communications commands and responses, recorded data, or library files.

DECIMAL FORMAT-

sets the decimal character used in decimal numbers on the display. Available options

are period (.) and comma (,). The default option is (.). This setting has no effect on communications commands

and responses, recorded data, or library files.

TEMPERATURE RESOLUTION-

sets the desired number of decimal places that appear in displayed tem-

perature measurements. Available options are 0.1 through 0.000001. The default option is 0.00001. The actual

number of decimal places of displayed temperatures may be reduced for large numbers. This setting has no

effect on communications commands and responses, recorded data, or library files. The resolution of displayed

resistances and resistance ratios is fixed at the maximum practical resolution.

SCREEN SAVER ENABLE-

enables or disables the screen saver. If Screen Saver Enable is OFF, the display

will remain on indefinitely. Enabling the screen saver saves power and extends the lifetime of the display. The

default option is OFF.

SCREEN SAVER DELAY-

sets the screen saver delay time. Available options are 5 min, 10 min, 15 min, 30

min, 45 min, 1 hr, and 2 hr. The default option is 1 hr.

DISPLAY BRIGHTNESS-

sets the brightness of the display backlight. Available options are 50 %, 60 %,

70 %, 80 %, 90 %, and 100 %. The default option is 100 %. Reducing the display brightness saves power and

extends the lifetime of the display.

ITS-90 SUBRANGE WARNING-

enables (ON) or disables (OFF) the warning message that appears at the

bottom of the Measurement Screen when a probe’s measured temperature exceeds its ITS-90 subrange by

more than 10°C. The default option is ON.

Rs DUE WARNING-

enables (ON) or disables (OFF) the warning message that appears at the bottom of the

Measurement screen when the due date of a resistor in the Resistor Library is past. The default option is OFF.

WARNING BEEP-

enables (ON) or disables (OFF) the audio indication that accompanies warning messages.

The default option is ON.

Содержание 1594A





































Результаты поиска

Содержание 1594A

Отзывы:

Похожие инструкции для 1594A

Бренды по названию

Популярные бренды

Fluke 1594A, Руководство пользователя

Результаты поиска

Содержание 1594A

Отзывы:

Похожие инструкции для 1594A

Бренды по названию

Популярные бренды