Fluidwell F127-P-EL-TA Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 52

background image

HF127PEN_EL_TA_v0501_04

Page 32

Pulse-signal NPN / NPN-LP:

The F127-P-EL is suitable for use with flowmeters which have a NPN output signal. For reliable
pulse detection, the pulse amplitude has to go below 1.2V. Signal setting NPN-LP employs a low-
pass signal noise filter, which limits the maximum input frequency - read par. 3.2.3.

Pulse-signal PNP / PNP-LP:

The F127-P-EL is suitable for use with flowmeters which have a PNP output signal. 3.2V is offered
on terminal 11 which has to be switched by the sensor to terminal 10 (SIGNAL). For a reliable pulse
detection, the pulse amplitude has to go above 1.2V. Signal setting PNP-LP employs a low-pass
signal noise filter, which limits the maximum input frequency - read par. 3.2.3.
A sensor supply voltage of 8.1 -12 or 24V DC can be provided via options PD-PM.
For a signal detection level of 50% of the supply voltage: please refer to “active signals”.

«
...
30
31
32
33
34
...
»

Содержание F127-P-EL-TA





















































Отзывы:

Нет отзывов

Похожие инструкции для F127-P-EL-TA

Бренд: Radio Shack Страницы: 276

Бренд: IBASE Technology Страницы: 32

Бренд: Precision Страницы: 5

Бренд: Fairlight Страницы: 439

Бренд: Elo TouchSystems Страницы: 3

Бренд: Vivo Страницы: 4

Бренд: TYAN Страницы: 33

Бренд: TYAN Страницы: 101

XPC Barebobe SZ87R6

Бренд: Shuttle Страницы: 14

Бренд: Shuttle Страницы: 13

Бренд: IEI Technology Страницы: 14

Бренд: Shuttle Страницы: 23

WorkFit-A, Single LCD Mount, LD

Бренд: Ergotron Страницы: 14

Бренд: Rise Страницы: 31

Бренд: MSI Страницы: 102

866441Y - Netfinity 5600 - 8664

Бренд: IBM Страницы: 276

Бренд: Gateway Страницы: 24

Бренд: Advantech-DLoG Страницы: 72

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды