Fluidmaster S2DBL Скачать руководство пользователя страница 13

Страница: 13 / 16

CONE

LOCK NUT

WASHER

WATER

SHUTOFF

FLAT

WASHER

COUPLING

NUT

LOCK NUT

COUPLING

NUT

LOCK NUT

COUPLING

NUT

COUPLING

NUT

WATER

SHUTOFF

SPIRAL

CONE

WASHER

WATER

SHUTOFF

WATER

SHUTOFF

BALL TUBING

METAL/COPPER

FLARED TUBING

METAL FLANGED

TUBING

METAL SPIRAL

TUBING

VINYL/BRAIDED

CONNECTOR

PLASTIC OR METAL

COMPRESSION

Use chart to determine the appropriate assembly parts required to properly reconnect the water supply.

DO NOT

use plumber’s putty to seal these fittings (Teflon tape optional). Do not use thread lubricants. Use of thread sealants or

lubricants can damage plastic nut and result in flooding and property damage.

Use Fluidmaster coupling nut
and cone washer to replace
existing parts. Water supply
tube must extend 1/2 inch
inside threaded shank of valve.

Use existing coupling
nut and existing flat
washer.

Use existing spiral
cone washer.

Captive cone washer
already included.
No additional
washers required.

Do not use Fluidmaster's
coupling nut and the
cone washer on plastic or
metal tubing as shown.

CAUTION: DO NOT

use CONE WASHER with PLASTIC SUPPLY LINE or METAL SPIRAL TUBING.

CAUTION

: Locknut and coupling nut should be hand tightened only! Over tightening locknut or coupling nut could result in

breakage and flooding.

Go to our website at www.fluidmaster.com for more information.

(Optional for Step 3.1) Identify union type

Completed installation

Содержание S2DBL

















Результаты поиска

Содержание S2DBL

Отзывы:

Бренды по названию

Популярные бренды

Fluidmaster S2DBL, Инструкция по установке

Результаты поиска

Содержание S2DBL

Отзывы:

Бренды по названию

Популярные бренды