FLOWCOMP GAS-NET 2 Series Скачать руководство пользователя страница 41

Страница: 41 / 54

Maintenance

gas-net

C1 and C2

Page 7-1

7 Maintenance

gas-net

devices do not require much maintenance.

7.1 Battery

Replacement

The device battery mainly runs down when the device is switched off. The bat-

tery consumption can be neglected as long as the device is switched on.

The battery should therefore be replaced after 5 years when in the meantime

the device has been switched off for a longer period of time. Otherwise it is

sufficient to replace the battery after 10 years at the latest.

If the battery must be replaced, this should only be executed by a service engi-

neer or trained expert for safety reasons.

Important: The old battery must be disposed properly; i.e. it must either be

returned to the distributor (Elster-Instromet Systems) or handed in at special

battery take-back facilities.

To exchange the battery, you need to open the housing of the

gas-net

device.

Proceed as described below:

•

A battery of the following type is required: lithium 3V CR ½ AA.

•

Save the device parameterization by reading it out with GAS-WORKS, to be

on the safe side. Read out the archives, too.

•

Disconnect the supply voltage.

•

Loosen the 4 fixing screws on the back of the device.

•

Slightly withdraw the mounting rail.

Attention

: The boards are sensitive! Avoid any contact with other compo-

nents!

•

The battery compartment is (seen from behind) on the board located back

at the top on the far right side. Detach the cover strap of the battery com-

partment with a screwdriver. Remove the old battery. Now you have 15

minutes for the battery exchange. During these 15 minutes a data backup is

guaranteed by a capacitor. Insert the new battery.

Содержание GAS-NET 2 Series























































Результаты поиска

Содержание GAS-NET 2 Series

Отзывы:

Похожие инструкции для GAS-NET 2 Series

Бренды по названию

Популярные бренды

FLOWCOMP GAS-NET 2 Series, Техническая документация инструкция

Результаты поиска

Содержание GAS-NET 2 Series

Отзывы:

Похожие инструкции для GAS-NET 2 Series

Бренды по названию

Популярные бренды