background image

 

 FLORIDA-PNEUMATIC.COM 

 

Please contact 1-800-356-3392 for further assistance.

Warranty

Limited Warranty: Universal Tool warrants its tools to be free from defects in material and workmanship for one year from the date of 
purchase. This warranty does not apply to tools which have been abused, misused, modified or repaired by someone other than Universal 
Tool or its authorized service centers. If a UT tool proves defective in material or workmanship within one year after purchase, return 
it to any authorized service center or Universal Tool freight prepaid. Please enclose your name, address and adequate proof of date of 
purchase and a short description of the defect. Universal Tool will,at its option, repair or replace defective tools free of charge. Repairs or 
replacements are warranted as described above for the remainder of the original warranty period. Universal Tool's sole liability  and your 
exclusive remedy under this warranty is limited to repair or replacement of the defective tool.
There are no other warranties expressed or implied and Universal Tool shall not be liable for incidental, consequential or special damages, 
or any other damages,costs or expenses excepting only the cost or expense of repair or replacement as described above.

Содержание Universal Tool UT8728













Отзывы: