Floor Doctor HFC-1, Руководство пользователя

Страница: 4 / 13

rugdoctor.com 1-800-784-3628
7 6
rugdoctor.com 1-800-784-3628
1. Before you begin, review the safety warnings found in the front of this manual.
2. Always test color fastness before using on surfaces.
a. Wet an inconspicuous area with a small amount of cleaning solution.
b. After 1-2 minutes, blot with a white absorbent cloth and check for color transfer.
3. Sweep or remove all loose debris from the area you want to clean to remove loose
dirt before using the Floor Doctor Hard Surface Cleaner machine.
1. If this is the first use, attach handle to main body by inserting the handle into the main
body until you hear the handle snap. The handle is now seated and secure.
2. Remove the cardboard nozzle protector from the nozzle.
3. Remove any additional packing materials from the machine and charger.
4. Place the machine on the storage tray near an outlet.
5. Plug the charger into the machine and then into the wall outlet.
6. Charge the unit for 6 hours (3.5 hours for recharge after use). Charge is complete
when the blue charge light quits blinking and remains a solid blue color.
7. Unplug the charger from the machine.
8. Remove the Clean Water Tank by pressing the tank release button and pulling the
water tank out the front.
9. Open the Clean Water Tank and fill with hot tap water, leaving enough room to add
solution. Do not use boiled or microwaved water in tank.
10. Add 1 tablespoon of Rug Doctor Hard Floor Cleaning solution to the clean water tank,
close the tank and replace it onto the main body.
11. With the unit on the hard surface to be cleaned, place your foot on the nozzle and
rotate the handle back to a use position.
12. Push the Power Switch on top once for low brush speed, twice for high brush speed
and a third time to turn the unit off again.
13. Use the solution trigger to activate the flow of solution. (It may take a few seconds for
solution to initially flow.)
14. Use slow forward and backward strokes to provide solution to the floor, brush the floor
thoroughly and lift the dirt off the floor with the suction nozzle.
NOTE: Suction is at the front of the nozzle, the backward stroke is the most
effective at lifting the dirt off the floor. The forward stroke loosens, provides solution
and prepares the surface for dirt removal in the backward stroke.
15. When finished, remove the Clean and Dirty Water Tanks, empty contents, clean and
dry the tanks before storage. Replace the dry tanks and place the unit back on its
storage tray ready for recharging.
16. Charge the unit so it will be ready for the next mess.
17. Charge unit periodically to maximize battery life.
CLEANING TIPS
QUICK START
OPERATION
Power Switch
Solution Trigger
1. Remove the cardboard nozzle protector.
2. Firmly insert the handle into the unit base until you hear the handle click into place.
a. If you do not hear the handle click into place, gently apply pressure until the handle
clicks into place.
3. To remove handle from the unit, first remove the screw. Once the screw has been
removed, utilize a tool to press the spring located to release the handle. Once
handle is successfully released remove the handle from unit base.
1. To fill the clean water tank, gently press Tank Release Button on the clean water tank
to release tank from the unit
(see picture #1)
.
2. Remove tank from the unit and fill with hot tap water, leaving enough room to add 1 tablespoon
of FloorDoctor hard floor cleaning solution as instructed on the solution bottle.
3. Once the water and solution have been added and place the tank back on the unit
pressing gently until you hear the tank click into place
(see picture #3)
.
Press Power Switch to start the machine
1. Press once for standard cleaning mode – Low Speed will have a blue light.
2. Press twice for boost mode for heavy dirt – High Speed with be a blue flashing light
3. Press third time to turn off the machine.
NOTE: Press the Solution Trigger when moving forward to release cleaning solution.
HANDLE ASSEMBLY
CLEAN WATER TANK INSTRUCTIONS
DO NOT USE BOILED OR MICROWAVED
WATER IN TANK.
Doing so could result
in scalding or burns and/or damage the
machine and void the warranty. Do not
walk on wet surfaces.
WARNING