background image

 

WARNING

 - Read and follow all instructions in this IOM manual and on the equipment. Failure 

to follow instructions can cause severe injury and/or death.

 

WARNING

 – 

Risk of Electric Shock . 

All electrical wiring MUST be in conformance with 

applicable local codes, regulations, and the National Electric Code (NEC). Hazardous voltage can 
shock, burn, and cause death or serious property damage. To reduce the risk of electric shock, do 
NOT use an extension cord to connect unit to electric supply. Provide a properly located electrical 
receptacle. 

Before working on any electrical equipment, turn off power supply to the equipment .

 

WARNING

 – To reduce the risk of electric shock replace damaged wiring immediately. 

 

WARNING

 – Ground all electrical equipment before connecting to electrical power supply. 

Failure to ground all electrical equipment can cause serious or fatal electrical shock hazard.

 

WARNING

 – Do NOT ground to a gas supply line.

 

WARNING

 – To avoid dangerous or fatal electrical shock, turn OFF power to all electrical 

equipment before working on electrical connections.

 

WARNING

 – Failure to bond all electrical equipment to system structure will increase risk for 

electrocution and could result in injury or death. To reduce the risk of electric shock, see installation 
instructions and consult a professional electrician on how to bond all electrical equipment. Also, 
contact a licensed electrician for information on local electrical codes for bonding requirements.

 

CAUTION

 – Potential pinch point. Equipment connected to or driven by this device may start 

unexpectedly and may cause personal injury or entrapment in linkage systems. 

Basic safety precautions should always be followed, including the following: Failure to follow instructions 
can cause severe injury and/or death.

 This is the safety-alert symbol. When you see this symbol on your equipment or in this manual, look 

for one of the following signal words and be alert to the potential for personal injury.

 

WARNING

 warns about hazards that could cause serious personal injury, death or major property 

damage and if ignored presents a potential hazard.

 

CAUTION

 warns about hazards that will or can cause minor or moderate personal injury and/or 

property damage and if ignored presents a potential hazard. It can also make consumers aware of 
actions that are unpredictable and unsafe.  

 

   A notice indicates special instructions that are important but not related to hazards.

 Notice:

IMPORTANT SAFETY INSTRUCTIONS

USE ONLY FLO-TITE GENUINE REPLACEMENT PARTS

ELo Rev C   ECR 044V

 

Page 

2

 of 28 

Back to TOC

www.flotite.com

Содержание PRO-torQ ELO Series





























Отзывы: