background image

 

TTCF-9A 

Variable High Flow Heated 

Hydraulic Component Flusher

 

40201409 

QUICK START 

INSTRUCTIONS 

 

Flo-Dynamics, Inc.  •  3300 Reedy Drive  •  Elkhart, IN 46514  •  800-303-5874

 

 

 

 

          

       

Page 

1

 of 

5

 

OPERATION 

 

SAFETY RECOMMENDATIONS 

This machine uses hot hydraulic fluid under pressure. Check the security of all hoses and connections before operation.  
Only use the same hydraulic fluid as used in the hydraulic system being flushed. DO NOT use mineral spirits, solvents, or any other volatile 

liquid.   
Always wear safety glasses, protective gloves, and proper clothing when operating the flusher. 
If hydraulic fluid gets in your eyes or on your skin, rinse with water immediately and seek medical attention if needed. 
WARNING: Improper use of this machine can result in burns and other serious injuries. Always wear eye protection and protective clothing, 

and follow instructions to prevent potential injury.

 

 

FLUSH PROCEDURE 

Fill the tank with 9 gallons of hydraulic fluid. Check the level 

with the dipstick (without threading in) to ensure the fluid 

level is between the high- and low-level marks.  
WARNING: DO NOT OVERFILL or run with fluid level 

above the high-level mark. 
Plug the machine into a 20A grounded circuit without 

anything else plugged in or being used on the circuit. If a 

dedicated 20A circuit is not available, use two separate 

dedicated 15A outlets. 
Connect the flusher to 100-125 PSI shop air.    
Move the Reverser Valve to the bypass (middle) position. 
CAUTION: Make sure the reverser valve is in the 

neutral/bypass position prior to preheating. 

 

 

 

 

 

 

Use the MODE button to select “START PREHEAT 

HEATER & PUMP” and select “CONT” using the RUN 

TIME button. 
Check the following: 

o

 

Secure fill cap 

o

 

Secure filter screen 

o

 

Check fluid level 

o

 

Check all connections 

o

 

Set flow rate 

o

 

Set flow direction 

Press the START/PAUSE button to begin heating the 

flusher while connecting the services hoses. 
 

 

 

 

 

Содержание TTCF-9A






Отзывы: