Analog
MPX
Connect to a
12V DC or 24V AC
power supply.*
Mounting
Surface
4 pcs
Ball Camera
Camera Base
Dome Cover
Image Sensor
1/3” 1.3MP CMOS
Video Format
NTSC (C234EC)/PAL (C234ECP)
Effective Pixels
H: 1305 V: 1049
Resolution
Digital: 720p
Analog: 960H
Scan System
Progressive
Sync System
Internal
S / N Ratio
≥
50dB (AGC Off)
Iris
AES
AES Shutter Speed
1/60 (1/50) ~ 1/60,000 sec.
Min. Illumination
0.1 LUX (IR Off)
0 LUX (IR LEDs On)
Video Output
Digital: 720p MPX HD-CVI
Analog: Composite 1.0Vpp @ 75ohm
Lens Focal Length / Type
2.8-12mm F1.4 / Varifocal
FOV (Horizontal)
Digital: 30-80°
Analog: 30-80°
Termination
BNC Type
IR Range / Qty.
100ft / 30m; 36 IR LED’s
Power Requirement
12V DC ± 10%
24V AC ± 10%
Power Consumption
12V DC: 500mA MAX with IR LED
24V AC: 315mA MAX with IR LED
Operating Temp. Range
–22° ~ 140°F / –30° ~ 60°C
Environmental Rating
IP66
Dimensions (W x H)
4.7” x 3.9”
120mm x 99mm
Weight
1.4lbs / 0.6kg
Camera Dimensions
Camera Specifications
To install the camera:
1. Use the included Allen key to
loosen the security screw on the
dome cover.
2. Rotate the camera base counter-clockwise to separate
it from the ball camera and dome cover.
3. Use the included mounting template to mark and drill
holes for the included mounting screws.
NOTE:
Insert the included drywall anchors if installing into
drywall.
4. Feed the camera cable through the camera base.
5. Connect the video and power cable as detailed in the
section ‘Setting up the Camera’.
6. Attach the camera base to the mounting surface using
the included screws.
7. Position the dome cover over the ball camera and twist
clockwise onto the camera base. Do not tighten completely.
8. Move the ball camera to the desired position. While
holding the ball camera in place, twist the dome cover the
rest of the way to secure it to the camera base. Holding
the camera prevents it from moving while tightening the
dome cover.
9. Use the included
Allen key to tighten
the security screw
on the dome cover.
Setting up the Camera
4.7” / 120mm
3.9”
99mm
ATTENTION:
Test the camera prior to selecting a permanent
mounting location by temporarily connecting the
camera(s) and cables to the DVR.
Installing the Camera
WARNING:
A REGULATED 12V DC or 24V AC power supply is REQUIRED for
use with this camera. Use of a non-regulated, non-conforming
power supply can damage this product and voids the warranty.
Camera Wiring
MPX
Connect to an MPX DVR for
720p viewing / recording.
Analog
Connect to an analog DVR for
960H viewing / recording.
1. Connect one of the two BNC connectors on the camera to the
video cable. See “Camera Wiring” for details.
2. Connect a power source to the power terminal block. The
camera supports both 12V DC and 24V AC power supplies.
NOTE:
Make sure to follow correct polarity as marked on the
power connector. For AC power, connect multiple cameras using
consistent wiring polarity to prevent video rolling.
Extension Cable Options
Specification
Maximum Length
RG59 20AWG Conductor 95% Braid
CSA/UL or C(UL) Approved
Up to 1500ft/455m
†
RG6 20AWG Conductor 95% Braid
CSA/UL or C(UL) Approved
Up to 2300ft/700m
†
Analog CCTV Balun
Up to 300ft/91m
† Long cable runs over 1000ft (300m) may be affected by
electro-mechanical interference (EMI), which can increase the
amount of noise in the picture in some installations.
The entire length of the cable run must be made using a single
extension cable between the camera and the DVR.
Adjusting Zoom & Focus
1. Use the included flathead screwdriver to adjust
the zoom and focus control screws as required.
2. Insert rubber weatherproofing plugs
(2x) into the zoom and focus screw-holes
to ensure a weatherproof seal.
* Camera focus may be affected if the power connection is too
long. It is recommended not to extend the power connection
past 200ft (61m).