Flintec FT-111 AN Скачать руководство пользователя страница 56

Страница: 56 / 146

FT-111(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019

Page

146

[

213

KEYSOU
N

YES ] Key sound

YES

:
:

Disable
Enable

[

214 REFRESH :

5 ] Display refresh rate

: 1...9 times/sec

[

22- INFO DISPLAY

]

INFORMATION DISPLAY

Press key or

key again to enter this menu.

Or press

key to go to the next sub-block.

[

221 TIME

D+T ] Information data on the right of the alphanumeric display.

T
D
D+T

:
:
:
:

No clock data on the display.
Display time,
Display date,
Display date and time,

[

222 DATA

TARE ] Information data on the left of the alphanumeric display.

TARE

GROS

:
:
:

No data
Tare weight is displayed
Gross weight is displayed in Net

[

23- START UP

]

START UP

Press key or

key again to enter this menu.

Or press

key to go to the next sub-block.

[

231 TARING

MULT ] Taring.

Page 36

MULT
GRO
S

:
:
:

Disabled.
Tare with key, via serial interface or via digital input.
Tare with key, via serial interface or via digital input
only at gross.

[

232 AUTO T

NO ] Auto taring.

Page 36

YES

:
:

Disabled.
Auto tare, if the gross load is bigger than MIN TARE
and stable.

[

233

AUTO
CLR

NO ] Auto clear.

Page 36

YES

:
:

Disabled.
Auto clear, if the gross load is lower than 10d.

[

234

PWR
TARE

NO ] Restore Tare at power on

YES

:
:

Disabled.
Tare value is saved at power off and the indication is
start in NET after switch on the instrument.

Содержание FT-111 AN



















































































































































Результаты поиска

Содержание FT-111 AN

Отзывы:

Похожие инструкции для FT-111 AN

Бренды по названию

Популярные бренды

Flintec FT-111 AN, Техническое руководство

Результаты поиска

Содержание FT-111 AN

Отзывы:

Похожие инструкции для FT-111 AN

Бренды по названию

Популярные бренды