background image

Thank you for purchasing our FlightLine OV-10A Bronco. It features an upper single-wing, double-engine, twin-tailed 
beam layout with a 1390mm length and a wingspan of 1400mm. It is made of EPO material and is reinforced with 
carbon and fiberglass. The modular design,  in addition to a small number of parts of the imitation decorative 
accessories, the body parts are fastened with screws. At the same time, the control board and the cable are used
to optimize the line connection. A dedicated wiring channel is designed inside the main wing for ease of use and 
maintenance, while retaining the overall integrity.

FlightLine RC OV-10A Bronco PNP version, with 3530-860KV brushless out-runner motor, 9507 three-blade 
propeller, 30A brushless ESC, 5A UBEC. The landing gear is controlled by an electric worm, the plastic has a 
s i m u l a t e d   a p p e a r a n c e   a n d   l a n d i n g   g e a r   s h o c k   a b s o r b e r.  T h e   l a r g e r   d i a m e t e r   f r o n t   a n d   r e a r   w h e e l s   ( w h e e l  
diameter: 65mm/70mm) are suitable for the take-off and landing of most grassland environments. The landing 
gear of the first three points is used, and the direction is easy to control during the take-off and running. The air 
p o s t u r e   i s   b e a u t i f u l   a n d   t h e   s t a b i l i t y   o f   e a c h   s p e e d   r a n g e   i s   g o o d .  A f t e r   s e t t i n g   c o r r e c t l y   a c c o r d i n g   t o   t h e  
instructions, when landing, open the flaps, the deceleration is obvious, and the posture is stable. Taken together, 
this model is suitable for a group of model enthusiasts who complete the propeller-type model entry exercises.

 1.This is not a toy! Operater should have a certain experience, beginners should operate under the guidance of
     professional players.
  2.Before install, please read through the instructions carefully and operate strictly under instructions.
  3.Cause of wrong operation,Freewing and its vendors will not be held responsible for any losses.
  4.Model planes’ players must be on the age of 14 years old.
  5.This plane used the EPO material with surface spray paint, don’ t use chemical to clean, otherwise it will damage.
  6.You should be careful to avoid flying in areas such as public places,high-voltage-intensive areas,near the highway,
     near the airport or any other place where laws and regulation clearly prohibit.
  7.You cannot fly in bad weather conditions such as thunderstorms,snows....
  8.Model plane’s battery, don’t allowed to put in everywhere. Storage must ensure that there is no inflammable
     and explosive materials in the round of 2M range.
  9.Damaged or scrap battery should be properly recycled, it can’t discard to avoid spontaneous combustion
     and fire.
10.In flying field, the waste after flying should be properly handled,it can’t be abandoned or burned.
11.In any case, you must ensure that the throttle is in the low position and transmitter switch on, then it can connect
     the lipo-battery in aircraft.
12.Do not try to take planes by hand when flying or slow landing process. You must wait for landing stop, then carry it.

1

Products introduction

Item No.:FLW305

Version No.: FLW305-01

FlightLine OV-10 Bronco

Содержание OV-10 Bronco














Отзывы: