Flextool MQ WHITEMAN EHHNK5 Скачать руководство пользователя страница 40

Страница: 40 / 54

EHHNK5 RIDE-ON TROWEL • OPERATION MANUAL — REV. #3 (05/03/21) — PAGE 39

MAINTENANCE (TROWEL)

3. Remove and retain the three screws that connect the

left-side CV joint assembly to the left-side gearbox

coupler (Figure 33).

Figure 33. Drive Belt Removal

4. Remove and retain the three screws that connect the

left-side CV joint assembly to the lower drive pulley

coupler (Figure 33). Slide the CV joint away from the
couplers to disconnect.

5. Cut and remove the existing drive belt. Ensure all belt

remnants are removed from the pulleys (Figure 33).

GEARBOX

COUPLER

LEFT-SIDE

CV JOINT

ASSEMBLY

LOWER

DRIVE

PULLEY

COUPLER

DRIVE

BELT

(CUT)

CLUTCH/

UPPER

DRIVE

PULLEY

SHORTER

SCREWS (3)

LONGER

SCREWS (3)

LEFT-SIDE

GEARBOX

NOTICE

The screws securing the CV joint to the lower drive

pulley coupler are shorter than those securing the

CV joint to the gearbox coupler. Remember screw

orientation for reassembly.

Drive Belt Installation

1. Place a new drive belt over the lower pulley (Figure 34).

Figure 34. Drive Belt Installation (Lower Pulley)

2. Squeeze the drive belt and pull upward and toward the

rear of the trowel (Figure 34). This will spread apart the
faces of the lower drive pulley.

3. Place the free end of the drive belt over the clutch, and

into the upper pulley groove (Figure 35).

Figure 35. Drive Belt Installation (Upper Pulley)

DRIVE BELT

LOWER

PULLEY

MOVING

FACE

FIXED

FACE

SQUEEZE AND

PULL UPWARDS

AND TOWARDS

REAR OF TROWEL

CLUTCH

UPPER

PULLEY

DRIVE BELT

Содержание MQ WHITEMAN EHHNK5























































Результаты поиска

Содержание MQ WHITEMAN EHHNK5

Отзывы:

Похожие инструкции для MQ WHITEMAN EHHNK5

Бренды по названию

Популярные бренды

Flextool MQ WHITEMAN EHHNK5, Руководство по эксплуатации

Результаты поиска

Содержание MQ WHITEMAN EHHNK5

Отзывы:

Похожие инструкции для MQ WHITEMAN EHHNK5

Бренды по названию

Популярные бренды